Where to Find the 2014 Dodge Durango Coolant Temperature Sensor: A Step-by-Step Guide

The coolant temperature sensor for the 2014 Dodge Durango is located near the bottom of the radiator on the driver’s side.

2014 Dodge Durango Coolant Temperature Sensor Location

The location of the coolant temperature sensor in the 2014 Dodge Durango can be accessed relatively easily. It is located in the left side of the engine, on top of the intake manifold. The sensor itself looks like a small metal rod, usually colored in either black or silver. The purpose of this component is to measure the engine’s temperature and send this information to the vehicle’s computer system. This data is critical for proper operation of components such as fuel injectors and spark plugs, as well as for efficient monitoring of your vehicles engine performance. Removing and replacing this component requires basic automotive knowledge, as removal can be somewhat tricky due to its under-the-hood placement. It’s important to keep an eye on this component to prevent any major failures in your Durango’s performance.

2014 Dodge Durango Coolant Temperature Sensor Location

It is important to understand the role of a coolant temperature sensor in your 2014 Dodge Durango, as well as its location. This component is responsible for monitoring the temperature of the engines coolant and sending a signal to the vehicles computer system so that it can adjust engine performance accordingly.

Identifying the Sensor

The coolant temperature sensor is typically located near the bottom of the radiator or close to one of the hoses coming off of it. It looks like a small metal tab that connects to two wires. It may also have an electrical connector on one end, and will usually be labeled as a coolant temp sensor or engine coolant temp sensor.

Locating the Sensor

Once you have identified and located the coolant temperature sensor on your 2014 Dodge Durango, you can then proceed with replacing it if necessary. The first step in this process is to remove any plastic shrouds or covers that are in place around it. Once these items have been removed, you should be able to see and access the sensor easily.

What Does It Do?

The purpose of a coolant temperature sensor is to monitor engine performance by measuring how hot or cold the engine’s coolant is at any given moment and sending an appropriate signal to the vehicle’s computer system so that it can adjust engine performance accordingly. If there is an issue with this component, such as when it fails to send out a signal at all, then your vehicle may not run as smoothly or efficiently as it should. This could lead to decreased fuel economy, increased emissions, and even engine damage over time if left unchecked.

What Is Its Function?

The function of a coolant temperature sensor is to measure how hot or cold your engine’s cooling system is at any given moment and send an appropriate signal back to your vehicle’s computer system so that it can make changes accordingly. If there are any issues with this component, such as when it fails to send out a signal at all, then your vehicle may not run as smoothly or efficiently as it should. This could lead to decreased fuel economy, increased emissions, and even engine damage over time if left unchecked.

Different Types of Sensors That Can Be Used

When replacing your 2014 Dodge Durango’s coolant temperature sensor, you will need to know what type of sensor you need in order for it to work properly with your vehicles computer system. Most vehicles use either an open-air type (which requires no wiring) or a closed-loop type (which requires wiring). You will also need to consider whether you want an analog (which has 3 wires) or digital (which has 4 wires) type of connector for connecting your new sensor into place.

Steps To Replacing The Sensor

Once you have determined which type of replacement coolant temperature sensor you need for your 2014 Dodge Durango, then you can proceed with replacing it following these steps:

Unplug any wiring harnesses from the old sensor before removing it from its mounting location on your radiator;

Loosen and remove any bolts holding the old unit in place;

Install new mounting hardware onto the new replacement unit;

Connect all wiring harnesses from both ends of your new unit;

Reattach any plastic covers over where necessary;

Start up your car and check that everything works correctly before driving off again!

The Consequences Of Not Having A Working Coolant Temperature Sensor On A 2014 Dodge Durango

If there are any issues with your vehicles coolant temperature sensor such as when it fails to send out a signal at all then this could lead to several problems including: decreased fuel economy due to inefficient combustion; increased emissions due to incomplete combustion processes; overheating due lack of regulation from not being able to detect when temperatures are too high; and even potential damage caused by extreme heat build-up within components such as pistons or cylinders due lack of warning signalled by failing sensors etc..

Benefits Of Upgrading Your Coolant Temperature Sensor On A 2014 Dodge Durango

Upgrading or replacing old faulty sensors on 2014 Dodge Durango can bring many benefits including improved reliability & safety while driving due more accurate readings being sent back from newer units; increased performance output due better regulation & control over temperatures under extreme conditions such as heavy loads etc.; reduced emissions due more efficient combustion processes being maintained through better monitoring & regulation etc..

Common Signs Of Faulty Or Failing Coolant Temp Sensors On A 2014 Dodge Durango

When the coolant temperature sensor on your 2014 Dodge Durango is not functioning properly, it can lead to many different problems. These problems can range from erratic engine behavior and lights, to sluggish acceleration and poor MPG. In order to identify these signs of a faulty or failing coolant temperature sensor, it is important to pay attention to any changes in the vehicles behavior when driving. If any of these signs become more frequent or noticeable, it is time to take your vehicle in for service.

Steps To Diagnosing A Faulty Or Failing Coolant Temp Sensors On A 2014 Dodge Durango

The first step in diagnosing a faulty or failing coolant temperature sensor on a 2014 Dodge Durango should be to check the vehicles codes and symptoms. This will allow you to determine if the engine is running too hot or too cold, which could indicate a problem with the coolant temperature sensor. After this initial assessment has been completed, it is important to perform component tests in order to determine if the coolant temperature sensor is actually malfunctioning. This may involve checking connectors and wires, as well as testing voltage levels with a multi-meter.

Best Practices & Tips When Diagnosing Or Replacing Your Coolant Temp Sensors On A2014Dodge Durango

When diagnosing or replacing your coolant temperature sensor on a 2014 Dodge Durango, it is important that you follow best practices and tips for safety and accuracy. Professional installation is always recommended when dealing with any type of automotive repair. Additionally, all components should be carefully examined for signs of wear or damage before attempting any repairs or replacements.

Tools You’ll Need When Conducting Repairs or Replacing your Coolant Temp Sensors On A2014DodgeDurango

In order to properly diagnose and replace your coolant temperature sensor on a 2014 Dodge Durango, you will need several different tools including a socket set and wrench set as well as electrical and hand testers. It is also important that you have access to the manufacturers service manual in order to avoid any costly mistakes during diagnosis or repairs. Additionally, protective gloves should always be worn when working with automotive components due to sharp edges that can cause injury.

FAQ & Answers

Q: Where is the coolant temperature sensor located on a 2014 Dodge Durango?
A: The coolant temperature sensor is located on the driver’s side of the engine, near the thermostat housing.

Q: What does a coolant temperature sensor do?
A: A coolant temperature sensor monitors the temperature of the engine’s coolant and sends this information to the vehicle’s computer. This allows the computer to adjust fuel injection, ignition timing, and other engine functions accordingly.

Q: What are some common signs of a faulty or failing coolant temp sensor?
A: Common signs of a faulty or failing coolant temp sensor include erratic engine behavior, sluggish acceleration, poor mileage, and warning lights coming on.

Q: What type of tools do I need when conducting repairs or replacing my coolant temp sensor?
A: Tools you will need when conducting repairs or replacing your coolant temp sensor include a socket set and wrench set as well as electrical and hand testers.

Q: Is it necessary to upgrade my vehicle’s coolant temperature sensor?
A: Upgrading your vehicle’s coolant temperature sensor can provide several benefits including increased performance output, improved reliability and safety, as well as better fuel economy.

The 2014 Dodge Durango coolant temperature sensor is located in the engine block, just above the oil filter. It is easily accessible and can be replaced with relative ease. The sensor is important for monitoring the engine temperature and should be inspected regularly to ensure proper operation of the vehicle.

Author Profile

Liberty Is Viral Desk
Liberty Is Viral Desk
Welcome to Liberty Is Viral, a digital nexus where curiosity is the currency and knowledge is the merchandise. We are not just another blog on the block; we are a movement, a collective of inquisitive minds committed to the ethos of liberating information and empowering individuals.

Our journey began with a simple yet profound belief: knowledge should be accessible to all, unrestricted by barriers, free as the air we breathe. Thus, in the bustling digital landscape of 2023, LibertyIsViral.com was reborn, a revitalized platform poised to quench the intellectual thirst of discerning netizens. And we can say we are a bit successful on that, since our community is expanding by the day (20,000 readers and increasing!)

Similar Posts