The likely cause of no heat on the passenger side in a 2012 Chrysler 200 is a malfunctioning blower motor, resistor pack, or heater core.

2012 Chrysler 200 No Heat On Passenger Side

The 2012 Chrysler 200 is a reliable and cost-effective sedan, but if you find yourself behind the wheel with no heat blowing out of the passenger side vents, it can become an uncomfortable situation. This problem is usually due to an issue with the HVAC system in the 200. If you have no heat on the passenger side, this guide will explain some of the possible causes and solutions so that you can get your car back on the road without feeling any discomfort.

First, there may be an issue with the blend door actuator. This component directs airflow to different parts of cabin via small doors; if it’s stuck in one place, heat won’t be able to flow to certain areas. Second, check your cabin air filter; if it’s blocked or clogged, air may not be getting into your car at all. Next, see if your vacuum hoses or system is leaking; this could lead to insufficient cooling in certain areas. Finally, there could also be a problem with your thermostat or coolant level; if either one isn’t working correctly, you won’t get adequate heating on any side of the cabin.

No matter what the cause turns out to be, fixing no heat problems on your Chrysler 200 is a process that requires attention and expertise to ensure that everything works correctly again. Having some experience under the hood is helpful but not always necessary; getting assistance from a trusted vehicle specialist can prove beneficial here as well. In any case, resolving this issue quickly and effectively should put you right back on track!

2012 Chrysler 200 No Heat On Passenger Side

Common Causes of No Heat on Passenger Side

No heat on the passenger side of a 2012 Chrysler 200 may be caused by a failed blend door motor, an actuator or control module, or a faulty thermostat. Troubleshooting the issue involves testing temperature readings and checking parts for faults. It is important to inspect the heater core for signs of clogging and replace if necessary. Additionally, testing the HVAC system pressures can help diagnose a faulty pressure switch and identify the need for replacement.

Troubleshooting a No Heat Issue

When troubleshooting a no heat issue on a 2012 Chrysler 200, it is important to check the temperature readings in order to identify any discrepancies that may be causing the problem. This can be done by running the climate control system and measuring the temperature of air coming out of both sides of the vehicle with an infrared thermometer. If there is an obvious difference in temperatures between both sides, then further investigation is needed to resolve this issue.

Testing the Thermostat

To test for faulty thermostat operation in a 2012 Chrysler 200, start by turning off all power to the HVAC system and disconnecting any attached wiring harnesses. Next, remove the thermostat housing cover and check for any blockages or debris that could be preventing proper operation. If none are found, then measure resistance levels with an ohmmeter or multimeter to check if any components are malfunctioning. If it is determined that replacement of a faulty thermostat is necessary, make sure to use only OEM-approved parts when installing a new one.

HVAC System Pressures Testing

In order to diagnose a faulty pressure switch on a 2012 Chrysler 200’s HVAC system, you will need to test pressures in both high and low side lines using special gauges that measure vacuum level differences between each side of engine compartment components such as condenser fans, evaporators, accumulators/drier tanks etc.. To do so correctly, you must first turn off all power sources connected to these components before attaching gauge hoses onto vacuum lines leading from them and taking pressure readings from each side while engine is running at idle speed. Once complete results are obtained from this process, compare them against manufacturer’s specs for proper operations in order to determine if problem lies within pressure switch itself or somewhere else in system.

Inspecting The Heater Core

If after completing all other necessary steps there are still issues with lack of heat coming from passenger side vents on your 2012 Chrysler 200 then it may be time to inspect heater core for signs of clogging. Symptoms indicating this possibility include reduced airflow volume through vents despite fan speed being set at maximum level as well as odd smells coming out whenever climate control system is turned on (i.e burnt plastic smell). In such cases replacing old core with new one should resolve problem quickly and easily without requiring too much effort from owner’s end other than following instructions provided by manufacturer regarding installation process itself.

Check for Blocked Coolant Flow in Radiator

When it comes to troubleshooting a lack of heat on the passenger side of a 2012 Chrysler 200, the first step is to check for blocked coolant flow in the radiator. This can be done by inspecting the radiator for debris or contamination that may be blocking the coolant flow. If any such debris or contamination is found, then it should be removed as soon as possible in order to restore proper coolant flow. Additionally, it may be necessary to flush the radiator and replace any contaminated parts if necessary.

Inspect Condenser Fan System

The condenser fan system should also be inspected when troubleshooting a lack of heat on the passenger side of a 2012 Chrysler 200. The condenser fan motor should be tested to ensure that it is running properly and providing adequate airflow through the system. If it is not running properly or not providing adequate airflow, then it should be replaced with a new one as soon as possible. Additionally, checking for any obstructions or blockages in the condenser fan system can help identify any problems that could prevent proper air flow through the system.

Inspect HVAC Control Modules

The HVAC control modules should also be inspected when troubleshooting a lack of heat on the passenger side of a 2012 Chrysler 200. If there are any issues with an inoperative control module, then fault codes retrieval and diagnostics should be done in order to identify and correct any issues with the control module. Additionally, checking for damaged or worn out components within the HVAC control module can help identify any potential problems that could cause an issue with temperature regulation within the system.

Check for Vacuum Leaks in HVAC System

The last step when troubleshooting a lack of heat on the passenger side of a 2012 Chrysler 200 is to check for vacuum leaks within the HVAC system. Vacuum leaks can cause numerous issues within an HVAC system and must be identified and repaired as soon as possible in order to restore proper temperature regulation within an HVAC system. Sources for vacuum leaks detection include looking for obvious signs such as visible cracks or holes in hoses, checking for loose connections between components, and using specialized equipment such as smoke machines or UV leak detectors to locate hidden leaks within an HVAC system. Once identified, these vacuum leaks must then be repaired using approved procedures and materials in order to ensure that they do not recur in future use.

FAQ & Answers

Q: What are the common causes of no heat on the passenger side?
A: Common causes of no heat on the passenger side include a failed blend door motor, blend door actuator/control module, and other faulty parts.

Q: How do I troubleshoot a no heat issue?
A: Troubleshooting a no heat issue involves taking temperature readings and resolving the issue by checking various parts.

Q: How do I test the thermostat?
A: Testing the thermostat involves checking for faulty operation and replacing it if necessary.

Q: How do I inspect the heater core?
A: Inspecting the heater core involves looking for symptoms of a clogged heater core, such as reduced air flow and water in the cabin, and replacing it if necessary.

Q: How do I check for blocked coolant flow in my radiator?
A: Checking for blocked coolant flow in your radiator involves troubleshooting blocked flow contamination and flushing your radiator to remove any debris.

The 2012 Chrysler 200 is notorious for having issues with the climate control system on the passenger side. The most common issue is no heat coming from the vents. The cause of this problem is usually due to a faulty heater core, which needs to be replaced in order to fix the issue. In some cases, it may also be caused by a malfunctioning blend door actuator, which can be reset and reprogrammed. If neither of these solutions works, then it’s time to seek out professional help from an experienced mechanic.