Troubleshooting Tips for When Your Ford Explorer Won’t Start But Has Power

The Ford Explorer has power but is not starting, likely due to a faulty battery or electrical issue.

Ford Explorer Wont Start But Has Power

If you have a Ford Explorer that won’t start but has power, you may have a problem with the ignition system or other components. Generally, ignition problems can cause your Ford Explorer not to start. This could be caused by a faulty starter, alternator, or battery which are all necessary for the engine to start. It could also be caused by a faulty spark plug, bad wiring, or other issues in the ignition system. In some cases, the ignition switch itself could be defective and need replacing.

Possible Reasons for Starting Issues

The most common cause of a Ford Explorer not starting but having power is a problem with the battery. The battery provides the initial jolt of power to the starter motor which then sets off the engine. If the battery is weak or has a dead cell, it wont be able to provide enough power to start the engine. Other possible reasons could include a starter motor malfunction or an electrical connection that has become loose or corroded.

Troubleshooting Steps To Diagnose The Issue

The first step in diagnosing this issue is to check the voltage of the battery. A healthy battery should have 12.4 volts when not in use, and 13.8 volts when its running. If its lower than these values, then you will need to replace your battery as soon as possible. Its also important to inspect all electrical connections and ensure they are clean and secure.

Testing and Replacing Possible Faulty Car Parts

If all connections are secure, then it may be necessary to test and replace any faulty car parts. This includes testing the starter motor solenoid, which can be done with a multimeter, as well as replacing any malfunctioning alternators which are responsible for charging the battery. Additionally, it may be beneficial to check for any worn out parts in your ignition system such as spark plugs or ignition coils which can cause misfires and starting issues if they are damaged or worn out.

Checking Out Any Fuel Issues

Sometimes fuel issues can also prevent your Ford Explorer from starting properly. To diagnose this you will need to check fuel pump pressure by using a fuel pressure gauge connected directly to the fuel rail on your engine block. Additionally, if you suspect there may be water or dirt contamination in your fuel tank you will need to test for this too as this can cause serious damage if left untreated.

Examining Ignition Or Spark Issues

Finally, its important to examine any ignition or spark issues that may be preventing your vehicle from starting properly. This includes checking if spark plugs are firing properly by using a spark plug tester and inspecting ignition coils for wear and damage which can prevent sparks from occurring when needed for combustion inside your engine cylinders – ultimately preventing your vehicle from starting at all!

Possibility of Computer Failure

It is possible for a Ford Explorer to fail to start even when it has power. One of the first steps in diagnosing the issue is to check the vehicles computer health status. This can be done by using a diagnostic scanner and looking for any intermittent or stored fault codes. If there are any codes present, they should be investigated and resolved before moving on to other potential causes.

Analyzing Other Potential Causes

If no fault codes are found, it is time to start examining hoses, filters, and belts. It is important to make sure that the serpentine belt is routing properly. Next, check that all of the hoses are connected properly and free of obstructions. Additionally, look at the air filter and fuel filter for debris or dirt buildup which could be restricting proper airflow or fuel flow.

Pro Tip for Fixing Starting Problems

A common cause for starting problems with a Ford Explorer is corrosion on the battery terminals. The terminals should be cleaned with baking soda and water mixture before attempting to start the vehicle again. If this does not work, using starting fluid can help diagnose an issue with engine compression which could also be preventing your car from starting properly.

How to Avoid such Problems in Future

To avoid future starting problems with your Ford Explorer it is important to keep up with regular maintenance service checks as well as adding a heavy duty jump starter to your cars toolbox in case of emergencies. Regularly checking your spark plugs, fuel injectors, and other components will help ensure that everything is running smoothly and prevent long term issues from developing over time.

FAQ & Answers

Q: What are the possible reasons for a Ford Explorer not starting?
A: Possible reasons for a Ford Explorer not starting include a problem with the battery, starter malfunction, fuel issues, ignition or spark issues, computer failure, and other potential causes.

Q: What are some troubleshooting steps to diagnose the issue?
A: Troubleshooting steps to diagnose the issue include checking battery voltage, inspecting electrical connections, testing the starter motor solenoid, checking fuel pump pressure and testing for fuel contamination.

Q: What are some possible faulty car parts that need to be tested and replaced?
A: Possible faulty car parts that need to be tested and replaced include the alternator, spark plugs and ignition coils.

Q: What is a pro tip for fixing starting problems?
A: A pro tip for fixing starting problems is cleaning corroded battery terminals and using starting fluid to diagnose engine compression.

Q: How can I avoid such problems in future?
A: To avoid such problems in future one should add a heavy-duty jump starter to their car’s toolbox and maintain regular service checks.

The Ford Explorer not starting but having power is likely due to an electrical issue. It is important to first check the battery connection and fuses, as these are often the cause of this kind of problem. If the battery connection and fuses are okay, then it is likely that an internal electrical component has failed or become damaged. In this case, it is best to take the vehicle to a qualified mechanic for further diagnosis and repair.