5 Tips to Bypass PATS System on Ford Taurus Cars

To bypass the PATS system on a Ford Taurus, you will need to have a knowledgeable mechanic reprogram the vehicle’s immobilizer.

How To Bypass Pats System Ford Taurus

The PATS (Passive Anti-Theft System) system in a Ford Taurus can be bypassed, allowing users to start their vehicle without a key fob. Bypassing the system requires some technical know-how, but it is not an impossible task. With the right tools and instructions, it is possible to bypass the PATS system safely and securely. This article will provide an overview of how to do just that.

To begin work on the bypass job, one needs to acquire a few necessary items: a special PATS bypass card, a pair of insulated needle-nose pliers, an automotive test light and some electrical tape. First of all, the wiring harness must be swiped with the patcher card this means running it along the circumference of all wiring harnesses in the engine compartment. The patcher card has markings showing which pins to connect and disconnect on each end. Once this is complete, one must use the pliers to cut open any plastic covering around wires so they can access them more easily.

Once that’s done, the automotive test light needs to be connected to each wire below where there will be two brown wires with two black pins in between them by sticking each into one side of the light connector until clicking sounds are audible when pulled out. With all wires being disconnected from each other (unless instructed not to), voltage must now be applied by switching on accessories such as headlights or windshield wipers so that certain signals get sent from control module to computer wire.

Finally, after performing this setup process and having confirmed success with voltmeter readings or audible locks engaged/disengaged sounds etc., it should result in successful bypassing of PATS system without having any issues whatsoever. You may have to cover these exposed wires with electrical tape or some other form of insulation after you’ve finished working with them in order to avoid potential electric shocks and issues due ingress/egress of moisture; however often re-taping/sealing isn’t necessary unless indicated as so itself during installation or setup stage itself.

Understanding PATS System

The Passive Anti-Theft System (PATS) is a security feature found on certain Ford vehicles. It functions by using a key with a transponder chip inside it that sends a signal to the vehicle’s computer when it is inserted into the ignition. If the computer does not recognize this signal, the vehicle will not start. Bypassing this system can be difficult, but it is possible with the right equipment and knowledge.

Identifying the Keys

In order to bypass the PATS system, you must first identify which key your vehicle uses. Most Ford Taurus models use an 80-bit transponder chip key. However, some models may use a different type of key so it is important to determine which one your vehicle uses before attempting to bypass the system.

Gaining Access to the System

Once you have identified which type of key your vehicle uses, you can begin to gain access to the PATS system. This requires removing the ignition lock cylinder and installing a bypass module in its place. This module will allow you to bypass the PATS system and start your vehicle without using a traditional key.

Necessary Equipment for Bypassing

In order to gain access to and bypass the PATS system, you will need several pieces of equipment:
– Required Tools for Removing Ignition Lock: These include various screwdrivers, wrenches and other tools that are necessary for safely removing and replacing the ignition lock cylinder from your vehicle.
– Bypass Module: This module will allow you to bypass the PATS system and start your vehicle without using a traditional key.
– Setting It Up: Once you have obtained the required tools and bypass module, it is important that you set them up correctly before attempting to start your vehicle.

Checking for Proper Setup

Once everything is set up correctly, it is important that you test it out before attempting to start your vehicle. This can be done by using an OBDII scan tool or code reader that supports transponder keys. These tools will allow you to check if all of the components of your bypass module are working properly and if they are properly connected to your vehicle’s computer system. Additionally, it is also important that you double-check all of these components before attempting to start your engine in order to ensure that everything is working as intended.

Disconnecting Battery and Replacing Components

Once everything has been tested out properly and all components are connected correctly, it is time to disconnect your battery from its terminals in order to prevent any electrical damage from occurring during installation or testing. After this has been done, you can then proceed with replacing all of the components back into their respective places including replacing or reinstalling any wires or cables that may have been disconnected during this process as well as replacing or reinstalling any additional parts such as ignition locks or key cylinders if needed . Finally, once everything has been put back together in its proper place, reconnect your battery terminals back together and test out if everything works as expected!

Programming New Keys to Enable Ignition

When attempting to bypass the PATS system on a Ford Taurus, the first step is to program new keys to enable the ignition. This can be done by having new keys programmed by a local dealer. Once the keys have been programmed, they should be inserted into the ignition switch. If successful, the PATS system will recognize the new key and allow for the vehicle to start.

Reconnecting Batteries and Starting Vehicle

Once new keys have been properly programmed into the PATS system, it is important to reconnect the batteries in order to start the vehicle. This involves connecting both batteries back together and then turning the key in the ignition switch. If successful, then there should be no issue starting up the vehicle.

Testing After Installation is Complete

Once all of these steps are complete, it is important to test that all systems are calibrated correctly and that everything has been installed correctly in order for vehicle operation to be safe. This includes making sure that all sensors are working correctly and that all systems are functioning properly. Once testing has been completed and all systems are functioning correctly, then it can be assumed that bypassing of the PATS system on a Ford Taurus has been successfully completed.

FAQ & Answers

Q: What is PATS System?
A: PATS stands for Passive Anti-Theft System. It is a security system that Ford has installed on its vehicles to protect them from theft. The system uses a special key with an embedded chip to start the vehicle, and if the wrong key is used, it will not allow the engine to start.

Q: What equipment do I need to bypass PATS System?
A: In order to bypass the PATS System on a Ford Taurus you will need a bypass module, various tools for removing the ignition lock, and new keys that will be programmed by a local dealer.

Q: How do I gain access to the system?
A: In order to gain access to the system, you must first remove the ignition lock from the steering column and then install the bypass module in its place.

Q: What steps do I take after installation of bypass system?
A: After installation of the bypass system, you must reconnect both battery cables back together and then insert new keys into the ignition switch in order for it to work properly. Finally, you should have your local dealer program these new keys so they can be used with your vehicle.

Q: How do I test that my installation is complete?
A: After installation is complete, you should use a scan tool to test all systems and make sure they are calibrated correctly before starting your vehicle. Additionally, it’s important that all peripherals of your PATS System are double-checked before taking your car out on the road.

The best way to bypass the PATS system on a Ford Taurus is to use a professional security bypass device. This device can be used to program the keys to the car and allow it to start without the PATS system. With this device, you can start your car even if you don’t have the original key. However, this should only be used as a last resort and it is always best to contact an authorized Ford dealer for any issues regarding the PATS system.