Troubleshooting Guide: How to Fix a Maytag Washer DRN Code

To fix the DRN code on a Maytag washer, contact either a local appliance repair service or call Maytag’s customer assistance number.

How To Fix Drn Code On Maytag Washer

If you are experiencing a DRN code on your Maytag washer, don’t worry – it’s an easy fix! A DRN code indicates a communication issue between the electronic control board and motor control. To begin the repair process, you’ll need to reset the error codes. First, make sure that the washer is unplugged for at least 1 minute. Then, press and hold the POWER button for five seconds. This should reset the error code. After that, plug the washer back in, followed by selecting any program and then hit START. Your Maytag washer should now be working properly and with no DRN code.

How to Fix DRN Code on Maytag Washer

Overview – The DRN code is a fault code that is displayed on the digital display of some Maytag washers. This code indicates that there is a problem with the internal connections of the washer. Common causes for this error can be loose wiring harness connections, pin jumper settings out of place, faulty components or insulation damage, and burned out electrical connectors. In order to diagnose and fix this issue, its important to understand the internal workings of the washer and consult an authorized technician if necessary.

Steps for Troubleshooting Your DRN Code

Quick Fixes – The first step in troubleshooting a DRN code is to check all internal connections of the washer. Make sure all wiring harnesses are securely connected, and that all pin jumper settings are properly placed. If everything appears to be in order, then you can move on to inspecting the interface board and its connections.

Depth Analysis – In order to inspect the interface board, you will need to access it from inside the washer cabinet. Once you have access to it, look for any signs of faulty components or insulation damage that could be causing an electrical connection problem. If there are any burned out electrical connectors, then these should also be replaced before moving on with your diagnosis.

Check For Internal Connections Issues

Loose Wiring Harness Connections – Loose wiring harness connections can cause a DRN error code on your Maytag washer. Its important to make sure all of these connections are secure before attempting any further troubleshooting steps. Make sure that all wires are tightly secured within their terminals and that none of them have been accidentally disconnected or shorted out by other components in the machine.

Pin Jumper Settings Out Of Place – Pin jumpers are small plastic inserts found near certain connectors inside your washer cabinet. These pins tell the machine which type of connection is needed at each point in order for it to function properly. If one or more of these jumpers have been moved out their proper position then this could cause a DRN error code as well as other issues with your washing machines operation. Check each jumper setting and make sure they are where they should be before moving on with your diagnosis process.

Inspect The Interface Board And Its Connections

Faulty Components Or Insulation Damage – Faulty components or damaged insulation can cause an electrical connection issue within your washers circuitry which can lead to a DRN error code being displayed on its digital display panel. Look closely at all components within the interface board for signs of corrosion or discoloration, which could indicate a shorted out circuit or other problem with its operation. Also check around any exposed wires for signs of fraying or cracking which could mean that some type of insulation has worn away over time causing an open circuit issue somewhere in the machine circuitry affecting its overall performance and leading to a DRN error being displayed on its digital display panel when trying to start up a wash cycle..

Burned Out Electrical Connectors – If you notice any burned out electrical connectors then these need to be replaced immediately in order for your washing machines circuitry to operate correctly again and prevent further issues from occurring such as DRN errors being displayed when attempting to run wash cycles with your machine..

Run Tests On The Motor Control Unit (MCU)

Verifying Voltage Output From MCU – In order for your washing machines motor control unit (MCU)to operate correctly it needs voltage output from its power supply so make sure this is present by testing its voltage output using a multimeter set up for AC voltage readings..

Bi-Directional Test Of The MCU – In addition to checking voltage output from the MCU you should also perform bi-directional tests using another multimeter set up in diode test mode while running through some basic diagnostic tests such as checking resistance between two points inside its circuitry.. This will help identify any potential issues within its circuitry that may have gone unnoticed during visual inspections prior such as broken wires or faulty components causing an open circuit issue somewhere inside leading up towards where it connects with other circuits within your washing machines main control unit (MCU).

Introduction

A DRN code on a Maytag washer can be an annoying problem to deal with. It is a code that typically indicates a communication error between the control board and the motor. Fortunately, this error can often be fixed by following a few easy steps. This guide will provide step-by-step instructions on how to diagnose and fix the DRN code on your Maytag washer.

Diagnosing the Problem

The first step in diagnosing the DRN code is to check for any loose connections or wires that may be preventing communication between the control board and the motor. If any of these connections or wires appear to be loose or damaged, they should be replaced before proceeding with further troubleshooting. Additionally, it is important to check the voltage of certain parts in order to ensure they are operating at their optimal level.

Replacing Faulty Parts as Necessary

Testing voltage of certain parts is an important part of this process. This can help determine if any parts are not functioning properly and need to be replaced. Damaged or inoperable parts should also be replaced if necessary in order to get your Maytag washer back up and running smoothly.

Final Steps and Resetting The Washer

After all necessary repairs have been made, it is important to clean all remaining parts of the washer for optimal performance. Once everything has been cleaned, it is time to perform a factory reset on your Maytag washer in order to get it back up and running again. This will reset all settings back to their original state so that you can start using your Maytag washer without any further issues.

FAQ & Answers

Q: What is a DRN code on a Maytag washer?
A: DRN stands for Door Reversal Not Detected. It is an error code that appears when the washer’s door does not close correctly or if the door switches are not aligned properly.

Q: What are common causes of the DRN code on a Maytag washer?
A: Common causes of the DRN code can include loose wiring harness connections, pin jumper settings out of place, faulty components or insulation damage, and burned out electrical connectors.

Q: How do I troubleshoot a DRN code on my Maytag washer?
A: To troubleshoot a DRN code, begin by checking for internal connections issues such as loose wiring harnesses and pin jumpers. Then inspect the interface board and its connections for any faulty components or insulation damage. Finally, run tests on the Motor Control Unit (MCU) to verify voltage output and perform a bi-directional test.

Q: What should I do if I need to replace any parts to fix my DRN code?
A: If you need to replace any parts in order to fix your DRN code, then you will first need to test the voltage of certain parts in order to determine which need replacing. Once you have identified which parts are damaged or inoperable, you can replace them as necessary.

Q: Are there any final steps I should take after fixing my DRN code?
A: After fixing your DRN code, it is important to clean any remaining parts of the washer such as its filter screen and interior tubs. Additionally, you should perform a factory reset in order to reset all settings back to their original state.

In conclusion, fixing the DRN code on a Maytag washer can be a difficult and time-consuming process. However, with the right knowledge and tools, it is possible to troubleshoot and repair most DRN code problems. It is important to identify the cause of the issue and address it accordingly to ensure that your washer remains in good working order.

Author Profile

Liberty Is Viral Desk
Liberty Is Viral Desk
Welcome to Liberty Is Viral, a digital nexus where curiosity is the currency and knowledge is the merchandise. We are not just another blog on the block; we are a movement, a collective of inquisitive minds committed to the ethos of liberating information and empowering individuals.

Our journey began with a simple yet profound belief: knowledge should be accessible to all, unrestricted by barriers, free as the air we breathe. Thus, in the bustling digital landscape of 2023, LibertyIsViral.com was reborn, a revitalized platform poised to quench the intellectual thirst of discerning netizens. And we can say we are a bit successful on that, since our community is expanding by the day (20,000 readers and increasing!)

Similar Posts