How To Put Jeep Wrangler In Neutral When Battery is Dead: Step-by-Step Guide

To put a Jeep Wrangler in neutral with a dead battery, use a screwdriver to move the ignition switch from the On position to the Accessory position.

How To Put Jeep Wrangler In Neutral With Dead Battery

If your Jeep Wrangler has a dead battery and you need to put it into neutral, don’t panic! Doing so is actually much simpler than you may think. By following the steps outlined below, you will be able to safely and easily complete the maneuver. First, locate the transmission shift boot or plastic cover near the center console. Remove it to expose the keyhole and inner shifter mechanism. Next, insert a flat-head screwdriver into the shift lever and twist counter-clockwise until it reaches its lowest position. Finally, push down on the shifter to disengage it from the neutral safety switch. With these three steps completed, your Jeep Wrangler is now in neutral and ready for towing or service.

Check Vehicle Status

Before starting the process of jump starting a Jeep Wrangler with a dead battery, it is important to check the vehicle’s status. Make sure that the emergency brake is engaged and that the gearshift lever is in Park. Additionally, make sure that all warning lights are off or dimmed. This will ensure that the vehicle is in a safe condition before attempting to jump start it.

Pulling Release Cable To Put Jeep Wrangler In Neutral From Park

Once the vehicle status has been checked, it is time to pull the release cable in order to put the Jeep Wrangler into Neutral from Park. This can be done by locating the gearshift lever release cable and pulling it gently until the lever moves into the Neutral position. Make sure that all warning lights are off or dimmed before continuing.

Check Warning Lights Once Jeep Wrangler Is In Neutral With Dead Battery

After putting the Jeep Wrangler into Neutral from Park and ensuring that all warning lights are off or dimmed, it is important to check all other dashboard lights as well as street and hazard lights to ensure they operate as designed. If any of these items do not work correctly, then further diagnosis may be required before attempting to jump start the vehicle.

Preparing Jeep Wrangler For Jump Starting With A Dead Battery

Once all of these steps have been completed, it is time to prepare for jump starting a Jeep Wrangler with a dead battery. Fasten cables to appropriate terminals on battery and starter safety, making sure you connect negative (-) first before positive (+). After this has been done, turn on your ignition key but do not start your vehicle yet. Finally, follow manufacturer instructions for assisting your vehicle with a jump start.

Turning Off Accessories Inside Jeep Wrangler With A Dead Battery

When your battery is dead, its important to turn off any accessories that may be draining the battery. The easiest way to do this is to unplug all adaptors and chargers from accessory ports. This includes items like phone chargers and USB cords. You should also make sure that all windows are completely closed, as well as making sure that headlights, heat/AC, and radio are turned off.

Checking Connections Before Jump Starting a Jeep Wrangler With A Dead Battery

Before you start jump starting your Jeep Wrangler with a dead battery, its important to check the connections between both vehicles. Make sure the cables are correctly connected on both cars, and make sure nothing is obstructing the connection of cables. Its also important to double check the wires to ensure positive on positive & negative on negative connection.

Completing the Jumpstart Process for a Jeep Wrangler with a Dead Battery

Once everything is connected up properly, its time to start jumpstarting your Jeep Wrangler with a dead battery. Start by slowly increasing the RPM of the possible car using gas pedal. As soon as you see it start running smoothly, slide gear into drive position as soon as possible car is running. Monitor lower flashing lights to monitor car returning back to normal.

Perform Checks After Jumpstarting A Jeep Wrangler with a Dead Battery

Once your dead battery is successfully jumpstarted, you should perform some checks before getting back on the road again. First and foremost, reconnect any equipment on the Jeeps interiors that you had previously disconnected during the jumpstart process. Make sure to recheck heat, air conditioner, and radio are turned OFF before reattaching any adaptors or chargers until it’s running normally again.

FAQ & Answers

Q: How do I check the vehicle status when jump starting a Jeep Wrangler with a dead battery?
A: Before attempting to jump start a Jeep Wrangler with a dead battery, it is important to check the vehicle’s status. This includes ensuring that the gearshift lever is in park and that the emergency brake is engaged. Additionally, it is important to ensure that all dashboard lights and street and hazard lights are functioning properly.

Q: How do I put a Jeep Wrangler in neutral with a dead battery?
A: To put a Jeep Wrangler in neutral with a dead battery, locate the gearshift lever release cable and pull gently. Once you have pulled the cable, verify that the gearshift lever has moved into neutral position.

Q: How do I prepare for jump starting my Jeep Wrangler with a dead battery?
A: Before attempting to jump start your Jeep Wrangler, ensure that all accessories such as headlights, heat/AC, radio and any adaptors or chargers are turned off. Additionally, make sure all windows are closed completely. After this is done, fasten cables to appropriate terminals on the battery and starter safety and connect negative (-) first before positive (+) terminal before turning on ignition key but not starting vehicle yet.

Q: What checks should I perform after jumpstarting my Jeep Wrangler with a dead battery?
A: After successfully jumpstarting your Jeep Wrangler with a dead battery, it is important to perform several checks. This includes reconnecting any equipment on the interior of the vehicle as well as making sure all accessories such as heat/AC and radio are turned off. Additionally, do not reattach any adaptors or chargers until the car has returned back to normal.

Q: What precautions should I take when cross verifying cables prior to jumpstarting my Jeep Wrangler?
A: Prior to cross verifying cables for jumpstarting your Jeep Wrangler, it is important to take several precautions for safety reasons. Make sure that all connections are correct between both vehicles and nothing is obstructing them from connecting properly. Double check wires to ensure positive on positive & negative on negative connections before proceeding forward with jumpstart process.

The best way to put a Jeep Wrangler in neutral with a dead battery is to use the transmission override. This procedure utilizes the shift rod and linkage to bypass the need for power from the battery. It is important to remember that this should only be done if you are parked on level ground and there is no risk of the vehicle rolling away. Once you have properly placed the Jeep Wrangler in neutral, you can then take steps such as jump starting or replacing the battery to get it back up and running.

Author Profile

Liberty Is Viral Desk
Liberty Is Viral Desk
Welcome to Liberty Is Viral, a digital nexus where curiosity is the currency and knowledge is the merchandise. We are not just another blog on the block; we are a movement, a collective of inquisitive minds committed to the ethos of liberating information and empowering individuals.

Our journey began with a simple yet profound belief: knowledge should be accessible to all, unrestricted by barriers, free as the air we breathe. Thus, in the bustling digital landscape of 2023, LibertyIsViral.com was reborn, a revitalized platform poised to quench the intellectual thirst of discerning netizens. And we can say we are a bit successful on that, since our community is expanding by the day (20,000 readers and increasing!)

Similar Posts