How to Fix the Kenmore Series 500 Washer Shaking During Spin Cycle

The likely cause of Kenmore Series 500 Washer shaking during the spin cycle is an unbalanced load.

Kenmore Series 500 Washer Shakes During Spin Cycle

Kenmore Series 500 Washers have been reported to shake or vibrate during the spin cycle. This is commonly caused by an unbalanced or overloaded load of clothes, a faulty part within the drum, or an unsecured washer. To resolve this issue, it may be necessary to both adjust and distribute the load inside of the washer and to check for loose components in the drum. If any parts are found to be loose, they should be tightened before recommencing the cycle. If the problem persists after these steps have been taken, a technician might need to be contacted.

Troubleshooting Common Issues

When troubleshooting a Kenmore Series 500 washer that shakes during its spin cycle, the first step is to check the drum balance. This can be done by starting a spin cycle and observing the washers movement. If the washer shakes or vibrates excessively during the cycle, then there is an issue with the drum balance. The next step is to check for worn suspension parts such as springs, shocks, and dampeners. These parts can wear out over time and cause the washer to shake during its spin cycle.

Preventative Maintenance Tips

In order to prevent issues with Kenmore Series 500 washers shaking during their spin cycles, it is important to follow a few preventative maintenance tips. One of these tips is to check the belt tension before each use. If the belt is too loose, then it can cause the washer to shake during its spin cycle. Additionally, it is important to make sure that the washer is level upon installation as an uneven surface can also lead to excessive vibration during use.

Additional Causes of Washer Shake During Spin Cycle

In addition to worn suspension parts and incorrect belt tension, other causes of a Kenmore Series 500 washer shaking during its spin cycle include loose drum assembly bolts and bad bearings or seals. Loose drum assembly bolts can cause excessive vibration if they are not tightened properly before use. Bad bearings or seals can also cause excessive vibration as they will no longer be able to contain the force of spinning inside of the machine.

Repair and Maintenance of Components

In order to repair any issues with a Kenmore Series 500 washer shaking during its spin cycle, it is important to inspect all components thoroughly before attempting any repairs. All drum assembly bolts should be checked for proper tightness and any worn suspension parts should be replaced if necessary. Additionally, any bad bearings or seals should be replaced in order for the machine to operate correctly again.

Kenmore Series 500 Washer Shakes During Spin Cycle

The Kenmore Series 500 washer is very popular, but some users have reported that their unit shakes and vibrates during the spin cycle. This can be a very annoying problem and can even damage your washer if not fixed. In this article, we will look at how to diagnose and fix this issue.

Rotate and Readjust Agitator

The first step in diagnosing a shaking or vibrating washer during the spin cycle is to rotate and readjust the agitator. To do this, turn off the power to the washer and remove the top of the agitator by unscrewing it from the base. Once removed, you should be able to see where the agitator has been rotating on its axis. If it looks like it has been spinning off-center, use a screwdriver to adjust it so that it’s centered again.

Verify Action of Agitator Movement Ratio From Motor to Suspension Arms

Once you have readjusted the agitator, you need to check how well it is transferring its movement from the motor to the suspension arms. To do this, turn on the power and let the washing machine run through its spin cycle while watching what happens at each of these points. If there is too much movement or vibration at either point then you may need to readjust or replace some of these components in order for your washer to work properly again.

Securing Agitator Movement With Hardware Clamps If Necessary

Finally, if your Kenmore Series 500 still shakes during its spin cycle then you may need to secure its agitator movement with hardware clamps if necessary. For this job, you’ll need clamps specifically designed for washing machines as regular clamps may not be strong enough for this purpose. Once secured firmly in place, your washer should stop shaking during its spin cycle and you can continue using it without any further problems.

FAQ & Answers

Q: What is the Kenmore Series 500 Washer?
A: The Kenmore Series 500 Washer is a top-load washing machine manufactured by Whirlpool. It features a large capacity drum and several customizable settings.

Q: Why does my Kenmore Series 500 Washer shake during the spin cycle?
A: There are several potential causes of this issue, including drum balance, worn suspension parts, loose drum assembly bolts, bad bearings or seals, and an improperly adjusted agitator whirlpool series 500 washer.

Q: How do I troubleshoot this issue?
A: Troubleshooting this issue should start with inspecting the drum assembly bolts, checking the belt tension and ensuring that the washer is level upon installation. If necessary, replace any worn suspension parts or bearings as well.

Q: How can I prevent this from happening?
A: Preventative maintenance tips include regularly checking the belt tension and ensuring that the washer is level upon installation. Additionally, regularly inspecting the drum assembly bolts can help detect any potential issues before they become more serious.

Q: What if these steps don’t solve the problem?
A: If these steps do not resolve the issue, then further inspection or repair may be necessary to determine if there are any additional causes of shaking during spin cycle such as bad bearings or seals. Additionally, verifying action of agitator movement ratio from motor to suspension arms and securing agitator movement with hardware clamps may be required in some cases.

The Kenmore Series 500 Washer is a great appliance, but if it shakes during the spin cycle, it is likely that the unit has an unbalanced load or a worn belt. If neither of those are the issue, then the problem may be due to a broken suspension spring or shock absorber and will require professional repair.