2013 Dodge Dart Rear Wheel Bearing Torque Specs: The Ultimate Guide for Vehicle Maintenance

The rear wheel bearing torque specs for the 2013 Dodge Dart are 150 ft-lbs (203 Nm).

2013 Dodge Dart Rear Wheel Bearing Torque Specs

The 2013 Dodge Dart is equipped with rear wheel bearings that require appropriate torque during installation. This guide outlines the torque specifications for these bearings and describes the most efficient methods for applying them. Installing and tightening the rear wheel bearings correctly is essential for prolonging the life of the vehicle. Failure to follow these torque specs can lead to excessive wear on the bearing components, leading to premature failure. By using the appropriate specifications for tensioning, Dodge owners can keep their Dart running smoothly for many miles to come.

Wheel Bearing Torque Specs

The wheel bearing torque specs for the 2013 Dodge Dart are as follows: Front Wheel Hub and Bearing Assembly to Knuckle Bolts: 150 lbs-ft; Rear Wheel Hub and Bearing Assembly to Knuckle Bolts: 175 lbs-ft; Wheel Lug Nuts: 100 lbs-ft. It is important to note that these torque specifications are for a standard wheel bearing and hub assembly, and may differ depending on the manufacturer.

Tools Needed

In order to properly torque the wheel bearing bolts on a 2013 Dodge Dart, you will need the following tools: a torque wrench, a socket set, an Allen wrench set, an open-end wrench set, and a breaker bar. It is also important to ensure that you have the correct size sockets and wrenches for your particular application.

Installing the Wheel Bearing

Before installing the wheel bearing on your 2013 Dodge Dart, it is important to ensure that all of the components necessary for installation are in good condition. This includes checking the knuckle bolts for rust or corrosion, as well as ensuring that all of the necessary mounting hardware is present. Once you have confirmed that everything is in order, you can proceed with bolting on the wheel bearing assembly.

Torquing Procedure

Once the wheel bearing has been installed onto your 2013 Dodge Dart, it is time to begin torquing down all of the bolts. Begin by torquing down each of the front knuckle bolts to 150 lbs-ft using a torque wrench. Make sure that each bolt has been tightened down evenly so as not to cause any damage or misalignment of parts. Next, move on to torquing down each of the rear knuckle bolts until they reach 175 lbs-ft of torque. Finally, use a breaker bar or other appropriate tool to tighten down each of your vehicle’s wheel lug nuts until they reach 100 lbs-ft of torque. Once all of your lug nuts have been tightened down correctly, your vehicle should be ready for use!

Torque Specifications

The torque specifications for the 2013 Dodge Dart rear wheel bearing are as follows:
Upper Control Arm to Frame: 110 ft-lbs.
Lower Control Arm to Frame: 80 ft-lbs.
Lower Ball Joint to Lower Control Arm: 80 ft-lbs.
Stabilizer Bar Link to Lower Control Arm: 30 ft-lbs.
Wheel Hub Assembly to Knuckle: 140 ft-lbs.
Wheel Lug Nuts: 90 ft-lbs.

Tools Needed

In order to properly torque the 2013 Dodge Dart rear wheel bearing, a few tools are needed. These include a torque wrench, socket set, and breaker bar. It is also important to have a clean work area so that the tools do not become dirty or damaged during the process of installing the wheel bearing.

Installation Process

The installation process for the 2013 Dodge Dart rear wheel bearing begins by first removing the wheel hub assembly from the knuckle and then unbolting the upper control arm from its frame mount point. Next, unbolt and remove the lower control arm from its frame mount point and disconnect any related components such as suspension links or ball joints that may be connected to it. Once all of these components have been removed, unbolt and remove the wheel hub assembly from its knuckle mount point on the axle housing. After this has been done, install any new components that may be necessary such as bearings or seals before reinstalling everything in reverse order of removal and torquing all of the bolts according to their specification above once they are tightened down properly.

FAQ & Answers

Q: What are the torque specs for the rear wheel bearings on a 2013 Dodge Dart?
A: The proper torque specs for the rear wheel bearing on a 2013 Dodge Dart is 89 lb-ft.

Q: Are there any special instructions for installing the rear wheel bearings on my 2013 Dodge Dart?
A: Yes, there are special instructions that must be followed when installing the rear wheel bearings on a 2013 Dodge Dart. The bearing should be pre-loaded to 0.002 to 0.004 with a torque of 89 lb-ft and then adjusted by rotating the spindle nut until it is snug. The bearing should then be tightened further until it reaches the specified torque of 89 lb-ft.

Q: How often should I replace my 2013 Dodge Dart’s rear wheel bearings?
A: Generally, it is recommended that you replace your 2013 Dodge Dart’s rear wheel bearings every 50,000 miles or 5 years (whichever comes first). If you use your vehicle in harsh conditions or drive more than average miles, it is recommended that you replace them more frequently.

Q: What do I need to do when replacing my 2013 Dodge Dart’s rear wheel bearings?
A: When replacing your 2013 Dodge Dart’s rear wheel bearings, you will need to remove the brake caliper, rotor and hub assembly before removing the old bearing and installing new ones. Additionally, you should inspect all related components including axle shafts and seals as well as lubricate them with grease during installation.

Q: Are there any other precautions I should take when replacing my 2013 Dodge Dart’s rear wheel bearings?
A: Yes, when replacing your 2013 Dodge Dart’s rear wheel bearings you should always make sure to use new hardware such as bolts and nuts and take care not to damage any of the components while working on them. Additionally, it is important to make sure that all related parts are properly lubricated during installation.

The correct torque specs for the 2013 Dodge Dart rear wheel bearing is 85 lb-ft. It is important to ensure the correct torque specifications are followed when replacing or servicing the rear wheel bearing. Failure to do so may result in damage to the wheel bearing, or other components, and could lead to a failure of the bearing. It is also important to use quality parts when replacing or servicing rear wheel bearings for maximum performance and longevity.