Where to Find the 2013 Ford Escape 1.6 Coolant Level Sensor

The coolant level sensor for a 2013 Ford Escape 1.6 is located on the passenger side of the engine.

2013 Ford Escape 1.6 Coolant Level Sensor Location

The 2013 Ford Escape 1.6 is equipped with a coolant level sensor. The sensor helps to detect the water levels in the cooling system, which is important for maintaining proper temperature. Locating the coolant level sensor on this model of Ford Escape can prove challenging, however, with a few simple steps you can easily find it. First, it is important to identify the engine’s air intake hose and tube connection. Once identified, moving around the tube toward the right side you will find the coolant level sensor. If you cannot locate it here, look for a round black plastic cap that has two pins sticking out from underneath it; this cap will house the coolant level sensor and will be connected to the cooling system’s lower radiator hose. With a bit of patience and close inspection of your engine, finding and checking your Ford Escape 1.6 Coolant Level Sensor should be easy and fast.

What is a Coolant Level Sensor?

A coolant level sensor is a type of sensor that monitors the amount of coolant in the cooling system of an engine. It usually takes the form of a float that is connected to an electrical switch, which sends a signal to the vehicle’s computer when the level of coolant drops below a certain point. The purpose of this sensor is to alert the driver when there is not enough coolant in the system, as low levels can lead to engine damage or even complete failure.

Location of Coolant Level Sensor in Ford Escape 1.6

The coolant level sensor in a 2013 Ford Escape 1.6 can be found near the top of the radiator on the passenger side. It is typically located just above where the upper radiator hose connects to the engine block. The sensor should be clearly visible and easy to access once you have located it.

Symptoms of Coolant Level Sensor Failure

When a coolant level sensor fails, there are several symptoms that may be present. The first symptom is usually an illuminated warning light on the dash, which indicates that there is a problem with either the coolant level or temperature within the engine cooling system. Other symptoms include rising engine temperature and difficulty starting or running your vehicle, as well as poor fuel economy and acceleration due to decreased combustion efficiency caused by reduced levels of coolant within the system.

Diagnosis of Coolant Level Sensor Failure in Ford Escape 1.6

In order to diagnose a failed coolant level sensor in your 2013 Ford Escape 1.6, it’s important to first check for any leaks or corrosion around it that may be causing it to malfunction. If no leaks are present, then you’ll need to check its voltage outputs with an ohmmeter or multimeter; if these readings are abnormal, then it’s likely that your coolant level sensor has failed and needs replacing.

Repairing Issues with Ford Escape 1.6 Coolant Level Sensor

If your 2013 Ford Escape 1.6’s coolant level sensor has failed and needs replacing, you’ll need to first disconnect its electrical connector from its wiring harness before removing it from its mounting location on top of your radiator reservoir tank cap assembly using a wrench or socket set depending on how tight it’s secured down by its nut fastener bolt head screw(s). Once removed, you can replace it with an identical new one before re-connecting its electrical connector and testing for correct operation using an ohmmeter or multimeter before reinstalling any other components you had removed during this repair process like air intake ducting parts etc..

Introduction

The 2013 Ford Escape 1.6 Coolant Level Sensor is an important component of the cooling system in your vehicle. It is responsible for monitoring the coolant level and alerting you if it drops below a certain level. In this guide, we will discuss the location of the coolant level sensor, how to access it and how to test it.

Location of the Coolant Level Sensor

The coolant level sensor is located on the side of the engine near the radiator. It is usually mounted on a plastic bracket and connected to two electrical connectors. Depending on your model, you may need to remove some components such as air intake ducts or other hoses in order to access it.

Accessing and Removing The Coolant Level Sensor

Before attempting to remove the coolant level sensor, make sure that you have disconnected both connectors from the terminals. This can be done by using a flathead screwdriver or a pair of needle nose pliers. Once both connectors have been removed, you can then proceed with removing the sensor from its mounting bracket by unscrewing two bolts that hold it in place.

Testing The Coolant Level Sensor

Once the coolant level sensor has been removed from its mounting bracket, it should be tested for proper operation using a multimeter set to read ohms (resistance). Connect one lead from the multimeter to each terminal on the sensor and check for continuity between them when they are both connected. If there is no continuity between them, then your coolant level sensor needs to be replaced immediately as it is not working properly.

FAQ & Answers

Q: What is a coolant level sensor?
A: A coolant level sensor is an electronic component that measures the amount of coolant in an engine. It sends a signal to the engine control unit (ECU) when the level is low, which triggers a warning light on the dashboard.

Q: Where is the coolant level sensor located on a 2013 Ford Escape 1.6?
A: The coolant level sensor for a 2013 Ford Escape 1.6 is located on the side of the radiator near the top. It can be accessed by removing the top radiator hose and unscrewing the sensor from its mounting bracket.

Q: What are some symptoms of a failing coolant level sensor?
A: Symptoms of a failing coolant level sensor can include warning lights on the dashboard, rising engine temperature, and fluctuating fluid levels in the radiator or other cooling system components.

Q: How do I diagnose a failing coolant level sensor on my 2013 Ford Escape 1.6?
A: To diagnose a failing coolant level sensor, first check for leaks and corrosion around it and then check voltage outputs from it with an OBD-II scanner or multimeter. If readings are abnormal, then further testing may be needed to confirm diagnosis.

Q: How do I repair issues with my 2013 Ford Escape 1.6’s coolant level sensor?
A: To repair issues with your 2013 Ford Escape 1.6’s coolant level sensor, you will need to replace it as well as any other related components that may have been damaged due to corrosion or wear and tear over time. After installation, you should test its voltage outputs again to ensure that everything is working correctly before putting your car back into service.

The coolant level sensor on a 2013 Ford Escape 1.6 is located underneath the hood on the passenger side of the vehicle. The sensor is connected to the radiator and is used to measure the coolant level in the system. It is important to keep an eye on your coolant level, as low levels can lead to engine damage. If you are unsure of how to locate and replace the sensor, it is best to contact a certified mechanic for assistance.