DIY Guide: How to Replace the String on a Bolens BL110 Trimmer

To replace the string in a Bolens BL110 trimmer, first remove the cover, then free the strings from the spool, cut new strings to length and wind them onto the spool.

Bolens Bl110 How To Replace String

Replacing the string of your Bolens BL110 string trimmer is a fairly simple task. This article will provide you with the steps you need to take in order to replace the string in your trimmer. With just a few basic tools, you can easily and quickly make sure that your trimmer is ready for use. First, you will need to locate and unlatch the bump knob cover on top of your trimmer spool. Then, remove the remaining line from the spool and discard it. Wind a new piece of line around the spool in an orderly fashion, according to your trimmer manufacturer’s instructions. Finally, re-attach the bump knob cover and shake out any excess line that may have been left behind during winding. Follow these simple steps and you’ll be well on your way to using your new string trimmer with ease.

Preparing to Replace the String

Replacing the string in your Bolens BL110 is a relatively straightforward task, but its important to be prepared and gather all the necessary tools before beginning. This will save you time and energy throughout the process. The tools you’ll need for this job include a Phillips head screwdriver, a pair of pliers, and some needle-nose pliers.

Identifying Components to be Replaced

Before starting any repairs, it’s important to identify which components need to be replaced. In the case of the Bolens BL110 string trimmer, these components include: spool and line casing, bump knob, spring washer and fastener. Identifying these components ahead of time will help you find replacement parts more easily and save time during the repair process.

Removing Old String

Now that you have identified all the components that need replacing, you can start removing the old string from your trimmer. Begin by taking out the spool and line casing from your trimmer, then remove the bump knob, spring washer and fastener using your Phillips head screwdriver or other tools. It’s important to take care when removing these parts as they are easily damaged if not handled correctly.

Cleaning and Inspecting Parts in Detail

Once all of the parts have been removed from your trimmer it’s time to give them a thorough cleaning before inspecting them for any signs of wear or damage. Start by cleaning off both sides of the spool and line casing with a damp cloth or brush to remove any dirt or debris that may have accumulated during use. Once this is done inspect all other components for signs of wear or damage such as cracks or frayed edges on the spring washer or fastener.

Replacing with New String

Now that all components have been cleaned and inspected its time to replace them with new string. Start by fitting in the spool and line casing with new string attached securely around them. Then put on bump knob, spring washer, and fastener securely ensuring they are tight enough so there is no slack when operating your trimmer. Make sure everything is tightened appropriately before testing out your newly repaired trimmer!

Reassembling the Bolens Bl110

If you have recently replaced the string on your Bolens Bl110 lawn mower, then you may need to reassemble it to ensure proper operation. The process is relatively straightforward and can be completed in just a few steps. First, make sure that all screws along the shrouds of the unit are tightened properly. This will help ensure that the string is properly tensioned when in use. Next, place the motor cover back over the unit and secure it with any screws or clips that may be necessary.

Final Touches to Ensure Proper Replacement of String

Once all of the components are put back together, there are a few final touches you should take to ensure that your string replacement was successful. First, cut off any excess string that may have been left after installation. This will help keep your lawn mower free from tangles and knots while in use, which can decrease its efficiency over time. Next, restart the unit and check to make sure that everything is working correctly. If everything seems to be running smoothly, then you have successfully replaced your Bolens BL110 string!

FAQ & Answers

Q: What tools are needed to replace the string on a Bolens Bl110?
A: You will need a screwdriver and a pair of pliers.

Q: How do I disassemble the Bolens Bl110?
A: First, you will need to loosen and remove the screws along the shrouds of the lawn mower. Then, carefully lift off the motor cover from over the unit.

Q: What components do I need to replace?
A: You will need to replace both the spool and line casing, as well as the bump knob, spring washer, and fastener.

Q: How do I replace with new string?
A: First fit in the spool and line casing with new string attached. Then put on the bump knob, spring washer, and fastener securely.

Q: What should I do after reassembling my Bolens Bl110?
A: After reassembling your lawn mower, its important that you check for any excess string that needs to be cut off. Finally restart the unit to ensure proper replacement of your string.

In conclusion, replacing the string on a Bolens Bl110 can be a simple process if one has the right tools and understands the steps involved. It is important to ensure that all safety precautions are taken, that the proper parts are used, and that all assembly instructions are followed. With these considerations in mind, anyone can easily replace the string on their Bolens Bl110.