Solving the Mystery of Dodge Dart No Crank No Start: A Guide

The cause of a ‘Dodge Dart No Crank No Start’ issue is likely an issue with the battery or a faulty starter.

Dodge Dart No Crank No Start

When it comes to a Dodge Dart no crank no start, it can be an intimidating problem to diagnose and fix. This guide will walk you through some of the most common causes and solutions of a no crank/no start issue in a Dodge Dart. With a bit of effort, you can get your vehicle back on the road quickly and safely.

The first thing to identify is the source of the issue; identifying this will help you narrow down possible solutions. Common causes of a no crank/no start issue in a Dodge Dart include the battery, starter, alternator or neutral safety switch.

The battery is the most common culprit, so first try checking if it’s clean, firmly connected and charged up fully. If it is none of these, jump start the battery using jumper cables and see if this solves your problem; if not, move on to other potential sources. The Starter could be faulty due to worn out brushes or clogged terminals. Another cause could be an alternator fault if this is the case it may need replacing or repairing as soon as possible. Check for any fluid leaks too as these can cause electrical issues that result in engine failure. Lastly check that your Neutral Safety Switch is functioning properly too; this is sometimes responsible when nothing else appears to be wrong.

Whatever you do make sure you follow safety precautions when diagnosing engine issues do not attempt repairs if you are not confident with what you’re doing! With time and effort it should be possible for you to diagnose and repair the problem yourself without having to take your car into a garage.

Checking the Battery

When troubleshooting a no crank/no start condition on a Dodge Dart, it is important to check the battery first. This is because the battery provides power to all of the vehicles electrical systems. If the battery is not providing enough power and voltage, none of the other components will be able to operate properly. The first step in checking the battery is to use a multimeter to test for voltage. If you dont have a multimeter, you can also use a voltmeter or battery tester.

The ideal voltage range for a fully charged battery should be between 12.4 and 12.7 volts. If your reading is below that range, then it is likely that your battery needs to be recharged or replaced. Additionally, you should also check for any signs of corrosion on the battery terminals as this could cause an electrical issue as well.

Jumpstarting the Car

If your reading shows that your battery has sufficient voltage but your Dodge Dart still wont start, then you may need to jumpstart the car in order to get it running again. This process involves connecting another vehicles battery with yours in order to give it an extra boost of power and get it running again. Make sure that you follow all safety precautions when jumpstarting a car and always wear protective gear such as gloves and safety glasses when working around electricity and batteries.

Diagnosing Faulty Alternator

If your Dodge Dart still wont start after jumpstarting then it could be due to a faulty alternator or starter motor. The alternator generates power for all of the electrical components in your vehicle so if it is not functioning properly it can cause significant issues with starting up your car. To diagnose this issue, you will need to use a multimeter or voltmeter once again in order to test for voltage at various points throughout the system such as at the starter motor, alternator, and other components such as fuses and relays.

Replacing Alternator

If tests reveal that there is an issue with your alternator then you will need to replace it in order to get your Dodge Dart running again. This process involves removing the old alternator from its mounting bracket and installing a new one in its place using bolts provided by most auto parts stores or online retailers dedicated specifically for repairing vehicles like yours.. Make sure that you consult with an automotive professional before attempting any repairs on your own as they may be able to provide additional insight into resolving this issue correctly without damaging any other components of your car while doing so..

Identifying Faulty Starter

The starter motor provides power from the engine which allows it turn over when starting up your vehicle so if there is an issue with this component then it can cause problems with getting your Dodge Dart started up correctly each time you attempt ignition. To diagnose this issue, you will need test for continuity across both sides of its solenoid switch using either a multimeter or continuity tester which should indicate whether there is an issue with its internal wiring or not.. Additionally, you can also remove its housing cover and visually inspect for any signs of damage such as burnt wires or corrosion which could be causing problems..

Repairing The Starter

In order repair any issues identified on the starter motor, you may need replace some of its internal components such as its armature windings or brushes depending on what tests reveal about their condition.. Additionally, some starters may require more extensive repairs which involve disassembling them entirely before being able inspect their individual parts more closely so make sure that consult an automotive specialist before attempting any repairs yourself otherwise risk damaging other parts while doing so..

Testing Ignition Switch With Multimeter

The ignition switch provides power from both sides of its cylinder in order turn over when attempting ignition so if there are any issues with this component then they could be causing issues when trying start up your Dodge Dart each time attempt ignition.. In order diagnose these issues ,you will need use a multimeter once again test both sides of switch by testing continuity between them using either resistance setting meter which should indicate whether there are any problems present internally preventing them transmission electricity through cylinder correctly.. Additionally ,you can also visually inspect switch itself determine whether there are any visible signs deterioration such corrosion on surface which could preventing them from functioning properly too ..

Replacing Ignition Switch

If tests reveal that there are indeed issues present internally within switch itself ,then may need replace entire unit order get back full functionality .. This process involves removing existing switch from dash panel disconnecting wiring harness attached back connector before being able install new one place .Once connected ,you can reattach wiring harness back panel reconnect negative side lead battery ensure everything functions correctly after installation .. Additionally ,some models require special tools removal installation process so make sure consult automotive specialist beforehand ensure correct procedure followed prevent damaging other components while doing so ..

Checking Fuses And Relays

Fuses and relays provide protection against too much voltage entering into certain circuits protect sensitive electronic components while relays control flow current certain points within electrical system .Therefore ,it important check these components ensure they working correctly when troubleshooting no crank/no start condition on Dodge Dart .In order do this ,you will need locate fuse box under dash panel check individual fuses see whether they blown out replaced along visual inspection relays determine whether they corroded damaged function correctly .Also note number written underside each relay keep track which ones been checked already prevent confusion during process ..

Replacing Fuses And Relays

Once all fuses relays have been checked determined faulty ,then can proceed replacing them .This involves disconnecting negative lead from battery unclipping cover fuse box checking individual fuses replacing those blown out along disconnected corroded relays installing new ones their place .Make sure consult automotive professional beforehand ensure correct procedure followed prevent damaging other parts during installation process ..

Wiring System

If your Dodge Dart won’t start, the first thing you should check is the wiring system. Broken cables and sockets can cause no crank no start issues, so it’s important to inspect them for any issues. Corroded connectors can also be a problem, so replacing them if needed is essential.

Fuel Pump

The fuel pump plays a key role in getting the engine started, so examining its status is also important. If it isn’t working properly, replacing it could be the solution you need to get your car running again.

Air & Fuel Filters

The air and fuel filters also need to be inspected and cleared or replaced as needed. Clogged filters can prevent your car from starting, so they are an important part of diagnosing a no crank no start issue with your Dodge Dart.

Crank Position Sensor

The crank position sensor can also cause a no crank no start issue with your Dodge Dart. Rather than replacing it, resetting the sensor may solve the problem without having to do costly repairs.

FAQ & Answers

Q: How Can I Check My Car’s Battery?
A: You should check your car’s battery by making sure its terminals are tight and clean. Also check for any signs of corrosion or damage, and test the voltage with a multimeter. If the voltage is lower than 12V, it may need to be replaced or recharged.

Q: How Do I Diagnose a Faulty Alternator?
A: To diagnose a faulty alternator you should first check for visible signs of damage such as broken wires or loose connections. Then you can use a multimeter to measure the voltage output of the alternator. If it is not in the appropriate range, then it may need to be replaced.

Q: How Can I Identify a Faulty Starter?
A: You can identify a faulty starter by listening for any strange noises such as clicking or grinding when trying to start the engine. You can also test the starter by connecting it directly to the battery and checking its current draw with an ammeter. If the current draw is too low, then it may need to be replaced.

Q: How Can I Test an Ignition Switch with a Multimeter?
A: To test an ignition switch with a multimeter, you should first turn off all power sources and disconnect any wiring from it. Then set your multimeter to measure resistance and connect one lead of your meter to each terminal on the ignition switch. The reading should be close to zero ohms if it is working properly. If not, then you will need to replace it.

Q: What Should I Do If My Car Won’t Start Due To Fuel Pump Problems?
A: If your car won’t start due to fuel pump problems, then you should first check that there is sufficient fuel pressure by connecting a fuel pressure gauge directly to the fuel line and turning on your ignition switch for at least 5 seconds before checking the gauge needle reading. If there is no pressure or insufficient pressure, then you will need to replace or repair your fuel pump accordingly.

Based on the research done, it appears that the most common cause of a Dodge Dart not cranking or starting is due to a dead battery or an issue with the starter. Other possible causes could be related to faulty wiring, faulty relays, or other electrical issues. It is important to thoroughly inspect the vehicle and diagnose the issue in order to properly repair it.