How to Easily Blackout Your Ford Emblem for an Updated Look

Remove the emblem from the vehicle and use rubbing alcohol to cover the emblem in black paint.

How To Blackout A Ford Emblem

Changing the appearance of your car can be a great way to make it stand out. If you have a Ford, one popular modification is to black out the emblem to give it a bolder look. With a few key supplies and basic handyman skills, you can easily customize your Ford grille in no time. To blackout your Ford emblem, you will need masking tape, painter’s tape, flat black spray paint, rubbing alcohol and newspaper. First, mask off the areas near the emblem with masking tape to protect them from paint overspray. Using painters tape, cover the existing emblem. Once securely covered with enough layers of tape, use rubbing alcohol and a paper towel to clean the surface of dirt and debris. Then place newspaper over any other parts of your car that don’t need painting and cover nearby ground surfaces with cardboard or an old sheet. Shake the can well before use and hold it 6-8 inches away from your car as you uniformly apply multiple thin coats of paint until desired coverage is achieved. Let dry for about 15 minutes before carefully removing all of your taped-off areas . Now enjoy your newly refreshed Ford!

Remove the Ford Emblem

Removing your Ford emblem is the first step to blacking it out. Depending on your vehicle, you may have to use a screwdriver to unscrew it from the grille or panel, or you may have to use a trim tool to pry it away. Be careful not to damage the paint or other parts of your car during this process.

Prepare the Work Area

Before you start blacking out your emblem, make sure youve prepared your work area properly. Clear away any clutter, and make sure you have enough lighting so that you can clearly see what youre doing. Youll also need some form of dust protection, such as a tarp or drop cloth, to keep any paint particles from getting onto your vehicle or other surfaces.

Clean the Ford Emblem

Now that your work area is set up and the emblem has been removed from the car, its time to start cleaning it. Begin by scrubbing it with soap and water to remove any dirt or grime build-up. Then use a degreaser to remove any oil residue that may be present. Make sure all of this dirt and grime is completely removed before proceeding with the next step.

Mask Off Unwanted Areas

Once your emblem is clean and dry, use tape freely around its edges in order to cover up any areas that need protection from paint overspray. You can also use heavy paper (like cardboard) cut into shapes for more detailed areas that need protection from paint overspray. Be sure not to cover up any areas where you want the new paint color to show through!

Prime and Paint Your Ford Emblem

It’s time for priming and painting! Start by spraying primer in multiple thin coats until all surfaces are evenly covered and protected from rusting over time. Then, using thin coats of color according to preference (black works well for a blackout look), apply several layers of paint until all surfaces are evenly covered and protected as well. Allow each coat of primer/paint plenty of drying time before moving on with additional coats.

Seal The Ford Emblem With Clear Coat Lacquer

Once all layers of primer/paint are dry, finish off by applying clear coat lacquer spray in either thin layers or multiple coats depending on what look you desire for your emblem. Allow at least an hour between each coat application so that everything has plenty of time for drying before moving on with additional coats if necessary for full coverage protection against rusting over time.

Reattaching The Blacked Out Ford Emblem

Once everything is completely dry, securely reattach the emblem back onto its original spot on your vehicle’s grille/panel with either screws (if necessary) or adhesive backing depending on what style of emblem was used originally for installation purposes in order for it not come off easily over time due to vibrations while driving etc.. An optional final step would be to seal edges with hot glue in order for extra protection against rusting over time if desired as well!

Tools Needed To Blackout a Ford Emblem

When blacking out a Ford emblem, the tools needed will depend on how the job is to be done. If you are using spray paint, you will need tape measurer/ ruler, masking materials (like heavy paper or masking tape) and a Phillips screwdriver or drill bit head bits. If you are using brush paint, you will need sandpaper, primer spray or brush paint and primer, clear coat/lacquer spray or brush paint.

Steps To Blackout A Ford Emblem

The first step is to remove the emblem from the car. This can be done with a Phillips screwdriver or drill bit head bits. After the emblem is removed, it should be thoroughly cleaned with soap and water.

Once the emblem is clean, use a tape measurer to measure out exactly how much area needs to be covered when painting. Mark off this area with masking material like heavy paper or masking tape. This will ensure that no unwanted areas are painted.

If using spray paint, it should be shaken for at least one minute before spraying on an even layer of primer over the entire area that needs to be painted black. Allow it to dry for at least 30 minutes before applying any additional coats of paint if needed.

For brush painting, sand down any rough spots on the emblem first and then apply an even coat of primer over the entire area that needs to be painted black. Once it has dried completely (at least 30 minutes), apply two coats of your desired color and allow them to dry completely before moving onto the next step.

Finally, apply one coat of clear coat/lacquer over the entire area with either a brush or spray in order to protect your finished product from dirt and other elements that could ruin it over time. Allow this coat to dry for at least 24 hours before reattaching your newly-blacked-out Ford emblem back onto your car!

FAQ & Answers

Q: What tools are needed to blackout a Ford Emblem?
A: You will need a tape measurer/ ruler, Phillips screw driver or drill bit head bits, sandpaper, spray paint or brush paint, primer spray or brush paint and primer, clear coat/ lacquer spray or brush paint, and materials for masking off unwanted areas such as heavy paper and masking tape.

Q: What steps are involved in blacking out a Ford Emblem?
A: There are several steps involved in blacking out a Ford Emblem. First you must remove the Ford Emblem from the car. Then prepare the work area by cleaning the emblem with soap and water and degreaser. After that you will need to mask off any unwanted areas with tape and heavy paper. Then you can prime and paint the emblem according to your preference. Finally seal the emblem with clear coat lacquer and reattach it when dry.

Q: How many coats of primer should I use?
A: You should apply primer in multiple layers of thin coats for best results. This will ensure that all areas of your emblem are covered with primer before painting.

Q: How long should I wait between each coat application?
A: You should wait at least an hour between each coat application of both primer and clear lacquer spray. This will give time for each layer to dry before applying the next one.

Q: Is there an optional final step for protection against rusting?
A: Yes there is an optional final step that you can use for extra protection against rusting on your Ford Emblem. After reattaching it securely, you can seal any edges with hot glue for added protection against rusting over time.

In conclusion, blacking out a Ford emblem is not a difficult task. With the right supplies and some patience, you can easily transform your Fords emblem into a unique look that stands out from the crowd. There are several methods that can be used to complete this project, and it all depends on how much time and effort you are willing to put in. Whether you choose to use plasti-dip, spray paint, or any other method, with a little bit of work your Ford will have a one-of-a-kind look for years to come.