How to Bypass a Maytag Dryer Start Switch: A Step-by-Step Guide

Unplug the power cord and use a flathead screwdriver to access the housing around the start switch, then push down on the lever to bypass the switch.

How To Bypass Maytag Dryer Start Switch

If you have Maytag dryer, you may be wondering how to bypass the start switch. To achieve this, you need to open up the interior of the dryer and locate the wires that are powering the switch. You will then want to disconnect these wires and install a jumper wire between them. This jumper wire will allow electricity to pass between the two ends, which will bypass the start switch and allow power directly to the motor. After replacing it with a jumper wire, double check all your connections are safe before powering on your dryer again. Following these steps ensures you know how to bypass Maytag’s dryer start switch safely and securely.

Initial Preparation

Before attempting to bypass a Maytag dryer start switch, it is important to have the right tools and materials on hand. Gather a Phillips head screwdriver, electrical tape, wire strippers, and any other necessary tools. Additionally, it is important to make sure the area where the work is being done is well-ventilated and free from any combustible materials.

Unplugging the Dryer

Before beginning the process of bypassing the start switch, it is important to unplug the dryer from its power source. Disconnecting cables from the dryer will prevent electric shock when working on or near wires. It is also a good idea to wear protective gloves when handling any type of wiring or components.

Removing the Access Panel

The next step in bypassing a Maytag dryer start switch is to remove the access panel. Use a Phillips head screwdriver to unscrew and remove any screws that are keeping the panel in place. Take out the access panel carefully so as not to damage any of its parts. Once removed, locate and identify all wires that are connected to or coming out of the start switch.

Locating and Disconnecting The Start Switch

Identifying wires and their connections to each other can be tricky in some cases; use caution when working with them so as not to cause any further damage or injury. After locating all wires connected with start switch, disconnect them carefully by removing contact button located at back side of it.

Connecting New Wires To Bypass Switch

Once all wires have been disconnected from start switch, attach wire terminals with components as required for bypass switch wiring setup according to manufacturers instructions. After attaching wire terminals securely double check for continuity using multimeter tool before powering up dryer again.

Reconnecting the Maytag Dryer Start Switch

When reconnecting the Maytag Dryer start switch, it is important to connect the wires to the contacts and secure them properly. This can be done by ensuring that the wire terminals are tight and secure, then connecting them to the contacts. Once the wires have been connected, it is important to test the connection for any loose or broken wires before proceeding with further repairs or replacements.

Installing New Start Switch

When installing a new start switch, it is important to adjust the release latch on the new switch before installing into the unit. This is done by adjusting the latching mechanism on the switch so that it fits securely in place. After installation, it is important to check that all connections are secure and that there are no loose wires or parts.

Replacing Access Panel Back onto Maytag Dryer

Once all repairs or replacements have been completed, it is time to replace the access panel back onto Maytag Dryer. This involves removing any screws holding the access panel in place and then reattaching it using new screws. It is important to ensure that all screws are tightened securely before using the dryer again.

Connecting Power at Circuit Breaker or Plug Outlet

The final step in bypassing a Maytag dryer start switch is connecting power at either a circuit breaker or plug outlet. Before doing this, however, it is important to verify voltage readings in order to ensure that there will be no issues when powering up your dryer. Once verified, you can then reconnect your plug socket and turn on your dryer again.

FAQ & Answers

Q: What tools do I need to bypass a Maytag dryer start switch?
A: You will need a Phillips head screwdriver and wire terminals with components to bypass the Maytag dryer start switch.

Q: How do I unplug the dryer to begin the bypass process?
A: To unplug the dryer, you must first disconnect the power and then remove any cables connected to it.

Q: Where is the start switch located on the Maytag dryer?
A: The start switch is located behind an access panel at the bottom of the dryer.

Q: How do I connect new wires to bypass the start switch?
A: You will need to attach wire terminals with components and test for continuity before connecting new wires to bypass the start switch.

Q: Do I need to replace the access panel when finished with the bypass process?
A: Yes, you will need to replace the access panel when finished with your project. Make sure that you secure all screws tightly before powering up your Maytag dryer again.

The best way to bypass a Maytag dryer start switch is to unplug the dryer and remove the front panel. Then, locate the start switch, disconnect it from the wiring harness and reconnect it directly to the motor. This will bypass the start switch and allow the dryer to start up without any problems. Additionally, be sure to check other components such as the thermal fuse before attempting this repair.