Find the Location of Your Intertherm Furnace Flame Sensor Easily

The flame sensor on an Intertherm furnace can usually be found on the burner assembly.

Intertherm Furnace Flame Sensor Location

The Intertherm Furnace Flame Sensor is an integral part of any Intertherm Furnace. It helps to ensure that the gas system is running safely and efficiently. Understanding the location of this important component is essential for any heating service professional.

The Flame Sensor can be found inside the furnace cabinet, typically attached very close to the main burner assembly. It is connected via a single electrical connection directly to the gas control valve. The intent of the sensor is to detect a pilot flame and, if present, allow for continued furnace operation, Otherwise, it will shut down the main burner assembly in order to prevent dangerous functioning.

Intertherm furnaces are equipped with a flame rectification sensing circuit that looks for certain properties present in clean burning flames. When starting up a new unit or performing repairs on an older one, checking and adjusting this part of the system can help ensure proper safe functioning of your furnace. Failing to adequately assess or maintain your Flame Sensor could be dangerous, so it’s important that you understand where your unit’s sensors are located and how they work.

Intertherm Furnace Flame Sensor Location

When it comes to the safety and efficiency of your furnace, one of the most important components to pay attention to is the flame sensor. This essential part of your furnace helps to ensure that your system is running efficiently, that it is not at risk for carbon monoxide poisoning, and that it will last as long as possible. The flame sensor is an integral part of your Intertherm furnace and knowing its location can be helpful in understanding how to properly care for it.

Types of Sensors

Intertherm furnaces are equipped with either a hot surface ignitor or a pilot light flame sensor. The hot surface ignitor sensor monitors the temperature of the igniter while the pilot light sensor monitors the flame from the pilot light. Either type of sensor works to detect any changes in temperature or flame intensity and will shut off the gas supply if a problem is detected.

Locating the Sensor

The location of your Intertherm furnace’s flame sensor will vary depending on which type you have. The hot surface ignitor will be located near or on top of the burner assembly, while a pilot light flame sensor will be located near or on top of the pilot light assembly. It is important to note that both types may be located in different places depending on your specific model, so refer to your owners manual for further details.

Benefits of an Intertherm Furnace Flame Sensor

Having a properly functioning Intertherm furnace flame sensor offers many benefits, such as helping to prevent carbon monoxide poisoning and extending its life span. By monitoring changes in temperature or flame intensity, it helps ensure that your system runs efficiently and safely by shutting off gas supply when a problem is detected. Additionally, it can help you avoid costly repairs by detecting problems early on before they become worse.

Care and Maintenance Tips for Intertherm Furnace Flame Sensors

In order to keep your Intertherm furnace running safely and efficiently, regular inspection and cleaning are necessary tasks that should not be overlooked. Inspecting each year before turning on your system helps you identify any potential problems so they can be addressed promptly before they become serious issues down the road. Cleaning should also be done yearly and involves removing any dirt or debris from around the burner assembly as well as wiping away any corrosion from around electrical connections if present. Additionally, replacing any worn out parts such as gaskets or seals when necessary can help keep your unit running smoothly for many years to come.

Important Safety Tips When Handling Intertherm Furnace Flame Sensors

When working with an Intertherm furnace’s flame sensors there are several important safety measures you should take into consideration: always avoid contact with electrical currents; wear proper protective clothing such as gloves; use caution when handling flammable materials; and never attempt repairs without first shutting off power supply at main breaker box or fuse panel located inside house. Additionally, always refer to manufacturers instructions when performing maintenance tasks so you can avoid potential hazards associated with improper handling techniques or inaccurate measurements being taken when troubleshooting common problems with these sensors.

Troubleshooting Common Problems with Intertherm Furnace Flame Sensors

When troubleshooting common problems with an Intertherm furnace’s flame sensors there are several things you should check for: first make sure all connectors and wiring are properly attached; then check functionality of ignitor or pilot light; make sure all other components such as gas valve are operating correctly; replace any faulty parts such as gaskets or seals if needed; clean burner assembly area regularly; inspect regularly for signs of corrosion around electrical connections; inspect for any damage caused by rodents chewing on wires; replace fuse if needed; keep area free from flammable materials like lint which could lead to fire hazard if ignited by overheating components inside unit due to buildup over time; and contact professional technician if further assistance is needed after troubleshooting all common problems associated with these sensors yourself without success in getting them resolved quickly so you can get back up running again without delay!

Intertherm Furnace Flame Sensor Location

Replacing an Intertherm furnace flame sensor can be a tricky task, especially if you don’t know where to look for it. This guide will explain where the flame sensor is typically located on an Intertherm furnace and what considerations to take when replacing it.

How to Replace an Intertherm Furnace Flame Sensor

When replacing an Intertherm furnace flame sensor, the first step is to disconnect the power supply. This will ensure your safety while working on the furnace. Once disconnected, you can then proceed with removing the old flame sensor. The exact removal method will depend on the type of furnace you have, so refer to your owner’s manual or contact a professional for assistance if needed.

Once you have removed the old flame sensor, it’s time to test the new one for optimal performance. To do this, you need to set up a functional testing system that will allow you to measure how well the new flame sensor is working. Once everything is set up, run some tests and make sure that your new flame sensor is working properly before proceeding with installation.

What to Consider When Choosing a Replacement Intertherm Furnace Flame Sensor

When selecting a replacement flame sensor for your Intertherm furnace, there are several compatibility requirements that must be taken into account. First and foremost, make sure that the replacement part is compatible with your particular model of furnace in order to ensure proper performance and safety. Additionally, consider factors such as size and resistance values before making your purchase.

Common Replacement Parts for an Intertherm Furnace Flame Sensor

When replacing an Intertherm furnace flame sensor, there are a few common parts that may need replacement as well. The most common parts include the furnace control board, ignition module and connector carrier assembly. Make sure that these components are in good condition before attempting any further repairs or replacements on your furnace.

By following this guide and taking into consideration all of these factors when replacing an Intertherm furnace flame sensor, you can rest assured knowing that your new part will be installed correctly and performing optimally for years to come!

FAQ & Answers

Q: What types of sensors does an Intertherm Furnace Flame Sensor use?
A: The Intertherm Furnace Flame Sensor utilizes a variety of sensors, such as thermocouples, thermistors, and photocells. Each sensor type is designed to detect different temperature ranges and provide a specific response.

Q: What are the benefits of an Intertherm Furnace Flame Sensor?
A: An Intertherm Furnace Flame Sensor can help to prevent carbon monoxide poisoning and extend the life span of the furnace by providing reliable flame detection. Additionally, it can help to improve the overall efficiency of the system.

Q: What are some care and maintenance tips for an Intertherm Furnace Flame Sensor?
A: It is important to inspect and clean the flame sensor regularly in order to ensure that it is functioning properly. Additionally, it may be necessary to replace the sensor if it becomes damaged or worn out over time.

Q: What safety tips should be followed when handling an Intertherm Furnace Flame Sensor?
A: It is important to avoid contact with any electrical currents when handling the furnace flame sensor in order to prevent potential injury or damage. Additionally, it is recommended that protective clothing such as gloves and glasses be worn for added protection.

Q: How do I replace an Intertherm Furnace Flame Sensor?
A: In order to replace an Intertherm Furnace Flame Sensor, first turn off all power sources connected to the unit before proceeding with removal of the old flame sensor. Once this has been completed, install a new flame sensor and test its functionality before powering up again.

In conclusion, the Intertherm Furnace Flame Sensor is typically located in the burner assembly of the furnace. It is important to refer to the furnaces owners manual for specific location information, as this can vary from model to model. Additionally, it is important to regularly check and clean the flame sensor to ensure optimal furnace performance.