How to Remove a Track Bar on a Jeep YJ: Step-by-Step Guide

Removal of the Jeep YJ track bar requires disconnecting all mounting hardware and bolts and carefully lifting it away.

Jeep Yj Track Bar Removal

Removing a track bar from a Jeep YJ is an easy task that can be completed in a few steps. The track bar, also known as the panhard rod, is a component of the steering system that helps keep the vehicle in alignment. To remove it, you will need to disconnect the wheel alignment shims and disconnect the ball joints at each end of the track bar. You should also always refer to your Jeep YJ’s manual for specific instructions on how to safely and properly remove a track bar from your vehicle. Once removed, you will be able to service wheel alignment and prepare for re-installation of your new track bar. With patience and basic tools, this is a relatively simple job for most do-it-yourselfers!

Gather Tools Needed for Jeep Yj Track Bar Removal

When it comes to removing a Jeep YJ track bar, you need to make sure you have the right tools. This includes a jack and jack stands, lug wrench, metric socket set, and a ratchet or breaker bar. Having these tools on hand will make the process easier and faster.

Disconnect YJ Track Bar from Steering Assembly

Once you have all of the necessary tools in place, you can begin to disconnect the track bar from the steering assembly. To do this, first raise the vehicle with a jack and support it with the jack stands. Then, loosen the bottom bolts of the track bar and remove any washers that are present.

Disconnect YJ Track Bar from Axle End

The next step is to disconnect the track bar from the axle end. To do this, first you will need to unbolt four nuts at the axle frame and remove any old bushings using a hammer. Then, remove any nut holding the track bar to its frame bracket using a ratchet and an extension.

Install New Components for Jeep YJ Track Bar Removal

After removing all of these components, you can begin installing new ones. Start by placing new bushings on the bracket of the axle and installing them tightly with a nut at its frame bracket using a ratchet and an extension. Then thread on a new cover plate over your steering assembly bolt, position washers, locking washer and nut onto it before tightening firmly with either your lug wrench or socket set as necessary.

Connect Upgraded YJ Track Bar Components to Steering Assembly

Once all of these components are in place, you can connect them up to your steering assembly by securing their nuts onto lower bolts before tightening their upper bolts attaching them with either your socket set or breaker bar as necessary. After that is done, your Jeep YJ track bar removal should be complete!

Connect Upgraded YJ Track bar Components to Axle End

Before attempting to reattach the track bar components to the axle end of your Jeep YJ, it is important to place washers on the upper bolts. This ensures that the components are properly secured and will not come loose during operation. Once the washers are in place, you can begin tightening the nuts at the axle frame using a torque wrench and following the specifications provided in your manual. It is important that you do not exceed this torque as it may cause damage or failure of your track bar components.

Return Front Wheels of the Jeep YJ To The Ground After Removing Tower Bars

Once all of your track bar components have been successfully attached, you can slowly lower your vehicle from its jack stands. Be sure to take extra caution during this process in order to avoid any unnecessary damage. Once on solid ground, you should then use a lug wrench to firmly tighten all lug nuts according to your manual’s torque specifications. This will ensure that your wheels are securely fastened and ready for use.

Check If There Is Any Slight Play in YJ’s Steering Wheel After Removal Of Track Bars

Finally, after removing all of your tower bars, it is important to check for any slight play in your steering wheel before taking it out for a spin. For this, you should begin by testing both left and right turns before proceeding further. During this process, be sure to look out for any discrepancies such as a loose steering wheel or excessive play that may indicate a problem with one or more of your track bar components. If everything appears normal, then you are ready to hit the road!

FAQ & Answers

Q: What tools are needed to remove the YJ Track Bar?
A: You will need jacks, jack stands, a lug wrench, metric socket set, and a ratchet or breaker bar.

Q: How do I disconnect the YJ Track Bar from the Steering Assembly?
A: First you need to raise the vehicle and support it with jacks and stands. Then loosen the bottom bolts of the track bar and remove the washers.

Q: How do I disconnect the YJ Track Bar from the Axle End?
A: Unbolt four nuts at the axle frame and remove old bushings with a hammer. Then remove the nut holding track bar to frame bracket using a ratchet and extension.

Q: How do I install new components for Jeep YJ Track Bar Removal?
A: Place new bushing on the bracket of axle and install nut tightly at frame bracket using a ratchet and extension. Thread new cover plate over steering assembly bolt, position washers, locking washer, and nut then tighten firmly with lug wrench or socket set.

Q: How do I return front wheels of Jeep YJ to ground after removing tower bars?
A: Lower vehicle from jacks stands slowly. Tighten lug nuts using lug wrench to torque specified by manual.

The removal of a Jeep YJ track bar is an easy process that requires only basic tools and some patience. With the right steps and attention to detail, the track bar can be quickly removed, allowing for the replacement of any faulty parts or a complete upgrade of the system.