How to Troubleshoot When JLG T350 Outriggers Won’t Go Up A Step-by-Step Guide

The outriggers on the JLG T350 will not lift.

Jlg T350 Outriggers Won’T Go Up

When it comes to JLG T350 outriggers, won’t go up can be a perplexing issue. But don’t worry – we’ll help you figure out what could be wrong. Generally the problem is caused by one of two causes: either the safety switch has not been engaged, or air has been trapped in the hydraulic lift pump. To diagnose and then fix the issue, here are some steps to take:
1. First, check the safety switch and make sure that it is properly engaged if necessary.
2. Then, if the safety switch is ok, prepare to remove any trapped air in the hydraulic lift pump. You’ll need a few special tools for this: a hand pump, some oil drain hoses, and an adjustable wrench or a 3/8″ ratchet wrench.
3. Now connect each of these pieces in the following order: hand pump – oil drain hose – adjustable wrench – hydraulic lift pump fitting (on outrigger). It’s important to have tight connections so that no air leaks out while pumping out of the system.
4. Now start pumping with your hand pump until you feel pressure building up into the system this means that all trapped air should have been expelled from within it and that all components have regained their normal pressure levels once again.
5. Finally, try lifting your JLG T350 again; if everything was done correctly, then your problem should now be solved!

JLG T350 Outriggers Won’t Go Up

When JLG T350 Outriggers fail to go up, it is important to investigate the cause of the malfunction. Common reasons for outrigger malfunction include outrigger motor issues and outrigger lock problems. It is essential to check the outrigger motors of the JLG T350 and inspect all external visible parts before attempting a repair solution.

Checking the JLG T350 Outrigger Motors

In order to determine whether an issue with the outrigger motors is causing malfunction, it is important to test and verify motor functionality. This can be done by running a diagnostic test which will indicate whether any components have been damaged or need replacement. Additionally, lubricating parts and cables can help improve motor performance and prevent further damage.

Fixing JLG T350 Outrigger Motors

If any components are found to be faulty or worn, they should be replaced in order to restore proper functioning of the motors. This may include replacing worn motor components such as brushes or bearings, as well as repairing any damaged wiring or connections. Additionally, replacing old hoses or fittings may also be necessary in order to ensure that fluids flow freely through the system without any restrictions.

Diagnosing JLG T350 Outriggers Locks

It is also important to check on filtration systems for outrigger locks as this can cause malfunction if filters become clogged or blocked. In addition, testing hydraulic valves and lines can help diagnose problems with lock performance that may not be apparent at first glance. If any leaks are found in either of these systems, it should be addressed immediately as this can lead to further damage over time if left untreated.

Repairing or Replacing JLG T350 Locks

When a JLG T350 Outriggers won’t go up, the first thing to do is to check the pressure ratings and look for any broken or worn components. Depending on the wear and tear, it may be necessary to replace parts of the lock system. This can be done by replacing individual components such as screws, washers, pins, and nuts. Additionally, it is important to check if there are any other problems with the lock system such as loose connections or misalignment before replacing parts.

Verifying New or Replacement Parts on JLG T350

Before installing new or replacement parts on a JLG T350 Outrigger, it is important to do basic testing and troubleshooting. This helps to ensure that the parts are working correctly and will not cause further damage. It is also important to validate certified factory models when replacing parts, as these are designed specifically for this model of outrigger.

Reassembling of the JLG T350 with New Parts

Once all new or replacement parts have been tested and verified, they can then be installed into the lock system of the JLG T350 Outrigger. This requires careful installation of both the motor and lock system in order to ensure that everything works correctly together. After installation is complete, all changed parts should also be retested for optimal performance before use.

Troubleshooting the Hydraulic System for JLG T350 Outriggers

In some cases, a faulty hydraulic system may be causing an issue with an outrigger’s ability to go up properly. If this is suspected, then troubleshooting should begin by analyzing exactly what the problem is through detailed diagnosis. This may involve checking connections between hydraulic lines for leaks or tightness as well as examining for any signs of wear and tear on mechanical components such as pistons and seals.

Testing Experienced After Repairing or Replacing JLG T3500

Once repairs or replacements have been completed on a JLG T3500 Outrigger’s Lock System or Hydraulic System, it is important to double check its working status by powering up machinery again. It is also crucial that a final running test should be executed in order to validate all repaired/replaced parts before using them again in any situation involving an outrigger lift equipment operation.

FAQ & Answers

Q: What are the symptoms of JLG T350 outriggers won’t go up?
A: The main symptom is that the outriggers will not move when the control is activated. The outriggers may also become stuck at an angle and not retract fully.

Q: What are the possible causes of JLG T350 outriggers won’t go up?
A: Possible causes include a faulty hydraulic pump, a damaged or blocked hydraulic line, a defective solenoid valve, or insufficient power to activate the system.

Q: How to troubleshoot JLG T350 outriggers won’t go up?
A: To troubleshoot this problem, check for any obvious signs of damage or blockage to the hydraulic lines, inspect the solenoid valve for proper operation, and test power supply to the machine. If possible, test the machine with a known working hydraulic pump in order to confirm that it is functioning properly.

Q: How can I fix JLG T350 outriggers won’t go up?
A: To fix this problem, replace any damaged components such as hydraulic lines or solenoid valves. If necessary, replace the hydraulic pump or other components in order to restore full operation of the machines outrigger system.

Q: Is it safe to operate a JLG T350 with its outriggers won’t go up?
A: No, it is not safe to operate a JLG T350 with its outriggers inoperable due to potential risks associated with incorrect operation of heavy machinery. It is recommended that any repair work should be undertaken by qualified and experienced personnel only.

The JLG T350 outriggers not going up can be a tricky problem to diagnose. It could be caused by a variety of factors, including hydraulic system issues, incorrect set-up and improper maintenance. It is important to inspect the entire system and all components thoroughly in order to determine the cause and correct the issue. With careful inspection and troubleshooting, you can get the JLG T350 outriggers back up and running in no time.