Where to Find the Blower Motor Resistor in a Kenworth T370 Truck

The blower motor resistor of a Kenworth T370 is located in the thermal housing near the driver’s side hinge post.

Kenworth T370 Blower Motor Resistor Location

The location of the blower motor resistor for the Kenworth T370 can be found in its cab. The blower motor resistor increases the speed at which air is passed through the ventilation system and assists with climate control in the cab. It’s important to ensure that this component is in working order, so knowing where it’s located is essential. This article provides an overview of the Kenworth T370 blower motor resistor location, including helpful tips and directions on how to identify and access it.

Kenworth T370 Blower Motor Resistor Location

The Kenworth T370 Blower Motor Resistor is an electrical component that regulates the flow of electrical current in the vehicle’s heating and cooling system. It is located in the engine compartment, typically near the blower motor. Proper installation and maintenance of this component is essential for ensuring safe and efficient operation of the vehicle’s climate control system.

Features and Components Used

The Kenworth T370 Blower Motor Resistor has two main components: a resistor and a connector. The resistor is made up of an aluminum core with a ceramic coating, while the connector is made of stainless steel or plastic. The resistor has two terminals – one for power input, and one for ground connection – which are connected to the blower motor through a wiring harness.

Installation Procedures

Before installing the Kenworth T370 Blower Motor Resistor, it is important to take certain precautions to ensure safety. The first step is to disconnect any power sources from the vehicle, such as the battery or alternator, and to make sure that all wiring harnesses are disconnected from their respective components. Once these steps have been completed, it is time to begin with the actual installation process.

The installation process involves attaching the resistor to its mounting bracket using screws or bolts, connecting its power input terminal to a 12-volt power source, connecting its ground terminal to an appropriate ground point on the vehicle’s chassis, and then securely fastening all wires using zip ties or similar fasteners. Finally, it is important to test that all connections are secure before proceeding with further repairs or maintenance tasks on this component.

Maintenance and Troubleshooting

To ensure proper performance of your Kenworth T370 Blower Motor Resistor, it is essential to regularly check its voltage and resistance values. If either value falls outside of its specified range, this could indicate a faulty connection or an issue with another part in your vehicle’s climate control system. In addition, identifying any faults in this component can help you determine if further maintenance or repairs are necessary before continuing with your journey.

Aftermarket Replacement Parts

When replacing your Kenworth T370 Blower Motor Resistor it is important to consider both cost and quality when selecting aftermarket replacement parts for this component. It is advisable to opt for parts that come from reputable manufacturers as these often offer higher quality components at more affordable prices than those offered by third party suppliers. Furthermore, when choosing aftermarket parts it may be beneficial to also purchase additional wiring harnesses as these can often be difficult to find at reasonable prices elsewhere due to their specialized design requirements.

Alternative Blower Motor Resistor Setups

In some cases upgrading your existing blower motor resistor setup may be beneficial depending on your specific needs or preferences as there are several retrofit options available on the market today such as electronic relays or adjustable wattage controllers which can provide additional features not found in traditional setups such as temperature sensing capabilities or increased efficiency ratings respectively. Additionally upgrading your setup may also provide other advantages such as increased safety due to improved insulation properties which can help protect against short circuits caused by loose connections in older models which could potentially cause fires if left unchecked for too long periods of time.

Kenworth T370 Blower Motor Resistor Location

The Kenworth T370 is a heavy-duty truck that features a blower motor resistor. The blower motor resistor helps regulate the speed of the blower fan. Its important to know where this component is located so that you can replace it when needed. This guide will provide an overview of the Kenworth T370 blower motor resistor location, as well as electrical connections for the blower motor resistor, tools used for a blower motor resistor replacement, and manufacturers specifications for the blower motor resistor.

Electrical Connections for the Blower Motor Resistor

When connecting electrical wiring to the blower motor resistor, its important to follow safety guidelines. Be sure to use appropriate wire guidance and wear protective gear to avoid potential electric shock or other hazardous situations. To ensure proper installation and operation of the component, its important to read and understand all instructions before beginning work.

Tools Used For a Blower Motor Resistor Replacement

A standard tool kit will typically include wrenches, pliers, wire strippers, and screwdrivers. Depending on your individual project requirements, additional specialized tools may be necessary to complete the job correctly and safely. If you are unsure about what tools are needed for your particular project, consult with an experienced professional or reference relevant product documentation before beginning work.

Manufacturers Specifications for the Blower Motor Resistor

Its important to familiarize yourself with manufacturers specifications for your particular model before beginning any work on your Kenworth T370 truck’s blower motor resistor. Output capacity regulations vary according to model type and size so be sure to check these specifications carefully before making any modifications or repairs. Additionally, some models may require additional components such as relays or fuses in order to operate correctly so be sure to reference product documentation when necessary.

FAQ & Answers

Q: Where is the Kenworth T370 Blower Motor Resistor located?
A: The blower motor resistor for the Kenworth T370 is located behind the glove box on the passenger side.

Q: What components are used for a T370 Blower Motor Resistor installation?
A: The components used for a T370 blower motor resistor installation include a resistor, mounting bracket, screws and wiring.

Q: What are some troubleshooting tips for a blower motor resistor?
A: Some troubleshooting tips include checking voltage and resistance values, identifying faults and testing the system with a multimeter.

Q: What are some alternative setups for a blower motor resistor?
A: Some retrofit options include upgrading to an electronic control unit or an aftermarket resistor that offers more control over fan speed.

Q: What tools are necessary for replacing a blower motor resistor?
A: Standard tools necessary for replacing a blower motor resistor include screwdrivers, wire cutters and pliers. Specialized tools may also be required depending on the type of installation.

The location of the Kenworth T370 blower motor resistor can be found on the passenger side of the engine bay. It is typically located near the firewall, just behind the blower motor itself. The resistor is essential for controlling the speed and power of the blower motor, so it should be checked regularly and replaced as needed.