Solving the Problem When Your Maytag Dryer Says ‘Sensing’ But Won’t Start

The issue could be caused by a faulty lid switch, clogged vent, or lack of power; it is recommended to have a professional inspect and service the dryer.

Maytag Dryer Says Sensing But Won’T Start

If your Maytag dryer is displaying the ‘Sensing’ indicator light, but not starting the cycle, it is likely due to one of five possible causes. The most common ones are: a clogged or blocked exhaust vent, a weak power supply, a faulty thermal fuse, a damaged drive belt, or faulty start switch. You can address these issues by: clearing and cleaning the exhaust vent; checking the electrical power supply; replacing the thermal fuse; and checking and replacing the drive belt or start switch if required. With some basic troubleshooting steps and components, you can get your Maytag dryer back up and running in no time!

Common Causes of Maytag Dryer Not Starting

When your Maytag dryer says sensing but won’t start, it could be for several reasons. The most common causes are a faulty thermal fuse or start relay/motor. The thermal fuse is a safety device that prevents the dryer from overheating and causing fires. The start relay/motor is responsible for starting the dryer when the dry cycle is selected. If either of these components are damaged or malfunctioning, the dryer will not start.

How to Test Thermal Fuse and Start Relay

In order to determine if either of these components are causing your Maytag dryer not to start, you can use a multimeter to test them. To test the thermal fuse, set your multimeter to measure resistance and place one probe on each end of the fuse. If there is no resistance, then the fuse has blown and needs to be replaced. To test the start relay/motor, place one probe on each terminal of the relay and check for continuity. If there is no continuity, then you need to replace the start relay/motor.

Other Possible Reasons Maytag Dryer is Not Starting

Aside from a faulty thermal fuse or start relay/motor, there may be other reasons why your Maytag dryer won’t start. One possible reason could be that you have selected a timed-dry cycle setting which will keep the dryer from starting until it reaches its predetermined time limit. Another possible reason could be that you have enabled an extended tumble feature which will keep the drum from spinning until it reaches its predetermined time limit as well.

How to Properly Reset Maytag Dryers

If you want to reset your Maytag dryers, you’ll need to first turn off its power supply in order to disconnect any current flow that may be present in it’s system. After doing so, unplug all electrical cords connected to it so that it can completely reset itself without any interference from other devices or appliances in your home. Once all cords have been disconnected, wait for at least 30 minutes before plugging everything back in and turning on its power supply again so that all settings can be properly recalibrated before attempting to use it again.

Troubleshooting Techniques When “Sensing” is Displayed on a Maytag Dryer

If “sensing” is displayed on your Maytag dryer screen but it won’t start when prompted, there are several troubleshooting techniques you can try in order to diagnose and fix any underlying issues with it’s system. The first step would be waiting at least 30 minutes before attempting to reset the unit which will give its internal systems enough time to cool down properly before restarting again; if this doesn’t work then you should clean out both its lint screen as well as its venting system which could also be clogged with debris preventing proper airflow within its components leading up its motor thus preventing it from turning on accordingly when prompted by user input commands

How to Check if the Controls are Functioning Properly

If your Maytag Dryer says ‘sensing’ but won’t start, one of the first things you’ll want to do is check if the controls are functioning properly. This can be done by diagnosing any problems with the electronic control board or timer. You can also test push button switches, spin switch, selector switch, heat switch and element circuit. If any of these components are not working properly, it could be causing your dryer not to start.

Alternatives When Diagnostics has Failed to Identify Cause of Problem

If diagnostics fail to identify the cause of the problem, there are a few alternatives you can try. First, check for any open circuit connections in the wiring harness. This can be done with a voltmeter or multimeter and probe tips. Additionally, inspect the heating element for any faulty conditions that could be causing your dryer not to start.

Necessary Items for DIY Maintenance Checks for Your Maytag Dryer

For performing DIY maintenance checks on your Maytag Dryer, you’ll need a few items. First and foremost is a screwdriver set. Additionally, you’ll need a noncontact voltage tester or multimeter and probe tips to check any wiring connections or components that may be malfunctioning.

Expert Maintenance Procedures When DIY Troubleshooting Doesn’t Work

When DIY troubleshooting doesn’t work in identifying why your Maytag Dryer isn’t starting, it may be necessary to seek out expert maintenance procedures from professionals who are familiar with this type of product. This could involve replacing parts such as thermal fuses and heating element assembly as well as performing professional level diagnostics performed by manufacturer technicians.

FAQ & Answers

Q: What are the common causes of a Maytag dryer not starting?
A: The common causes of a Maytag dryer not starting can include a thermal fuse, start relay or motor, timed dry cycle setting enabled, extended tumble feature selected, open circuit connections in the wiring harness, and faulty conditions with the heating element.

Q: How can I test the thermal fuse and start relay in my Maytag dryer?
A: To test the thermal fuse, you will need to remove it from the dryer and use an ohm meter to check for continuity. To test the start relay or motor, you will need to use a multimeter to measure voltage on each of its terminals.

Q: How do I reset my Maytag dryer?
A: To properly reset your Maytag dryer, you will need to first turn off the power supply to disconnect current flow. Then unplug all electrical cords from the unit. After that you can plug it back in and turn on the power supply again.

Q: What troubleshooting techniques should I use if sensing is displayed on my Maytag dryer?
A: If sensing is displayed on your Maytag dryer, it is recommended that you wait for 30 minutes before resetting the unit. Additionally, it is important to clean the lint screen and venting system as this may help resolve any issues with sensing.

Q: What items do I need for DIY maintenance checks on my Maytag Dryer?
A: For DIY maintenance checks on your Maytag Dryer you will need a screwdriver set and noncontact voltage tester/multimeter & probe tips in order to diagnose problems with electronic control boards or timers as well as testing push button switches, spin switch, selector switch, heat switch and element circuits.

The most common cause of a Maytag dryer not starting when the “sensing” light is on is a faulty start switch. If this is the case, it will need to be replaced in order to get the dryer working again. If the start switch appears to be functioning properly, then there could be a problem with one of the other components in the dryer such as an issue with the drive belt or motor. In these cases, it will be necessary to take apart the dryer and inspect each component for any signs of damage or malfunction.