Check Your Remington 710 Serial Number Now: Here’s How to Know If You’re Affected by the Recall

Remington Ammunition, Inc. has issued a recall for certain lots of Remington Model 710 and 715 rifles, which can be identified by the serial numbers located on the sidewall of the receiver.

Remington 710 Recall Serial Numbers

Remington 710 Recall Serial Numbers Remington has issued a voluntary recall of the 710, 715 and 770 series of rifles due to a potential safety issue. If you own any variation of the model, it’s important that you know your rifles serial number. This will help determine whether your firearm is included in the recall. If so, Remington will provide free repairs or replacements for them to ensure their safe use. Serial numbers on recalled models range from SRxxxxx (x values between 4,000 and 6,400) or RRxxxxx (x value between 0011 and 1097). To find out your rifles serial number, check the left side panel of the receiver; if the model is affected by the recall, take it to a Remington Authorized Service Center immediately.

Remington 710 Recall Overview

In April of 2015, Remington issued a recall on their Model 710 and 715 firearms due to a product defect that could cause the rifle to fire when the safety was not engaged. The manufacturer indicated that all recalled serial numbers had been stamped with the prefix F47 followed by four numbers and then a letter. Impacted serial number models included: F47XXXA, F47XXXS, F47XXXV and F47XXXW. The product defects involved issues with the firing pins that could cause accidental discharges when the trigger was pulled even if the safety was in the on position.

Recalled Remington Model Details

The manufacturer of the recalled firearms is Remington Arms Company, LLC (Remington). Consumers can contact Remington at 1-800-243-9700 or via an online form located on their website for more information about this recall. The product features associated with this recall include: bolt action rifles chambered in .270 Winchester, .30-06 Springfield, .300 Savage and .35 Whelen calibers; short action rifles chambered in .223 Remington; and long action rifles chambered in .25-06 Remington, 6mm Remington and .308 Winchester calibers. The defects associated with these firearms included issues with the firing pin that could cause accidental discharges when the trigger was pulled even if the safety was in the on position.

Government Regulations & Recalls Involved

The U.S. Consumer Product Safety Commission (CPSC) is responsible for enforcing product recalls such as this one from Remington Arms Company LLC (Remington). The CPSC provided specific instructions to customers regarding how they should proceed if they have one of these firearms: customers should immediately stop using their firearm and contact Remington to receive a free replacement bolt assembly which will be installed by an authorized service provider at no charge to them.

Investigating Your Firearms Serial Number

Consumers who own firearms manufactured by Remington should investigate their firearms serial number to determine whether it is affected by this recall. They should look for any letter or number combination beginning with F47 followed by four numbers and then a letter. Affected serial numbers include: F47XXXA, F47XXXS, F47XXXV and F47XXXW. If your firearm has one of these prefixes then it may be affected by this recall and you should contact Remington immediately for assistance.

After You Find Affected Firearm Model

If you discover that your firearm is part of this recall from Remington Arms Company LLC (Remington), then you should immediately stop using it until it can be replaced or repaired by an authorized technician at no cost to you. Under no circumstance should you use your firearm until it has been properly serviced according to instructions provided by Remington or its authorized service providers as doing so could result in serious injury or death. Additionally, there has been some controversy surrounding these recalls due to potential liability issues between consumers and manufacturers related to safety defects in their products which were not disclosed prior to purchase or use by consumers.

Remington 710 Recall Serial Numbers

Remington has recently recalled a number of their 710 model rifles due to a defect in the trigger assembly. The recall affects rifles with serial numbers between 85112500 and 85116400. If you own a rifle with one of these serial numbers, you should contact Remington to arrange for a free replacement.

Remington Replacement Procedures

Replacing your recalled Remington 710 rifle is a simple process. First, contact Remington at the phone number or email address provided on their website. They will provide you with instructions on how to return your rifle and arrange for a replacement. You may be asked to provide proof of purchase and/or other identifying information about the rifle in order to expedite the process.

Which Firearms Can Be Replaced?

The recall only affects Remington 710 rifles with serial numbers between 85112500 and 85116400. Any other models or variations of the Remington 710 are not affected by this recall.

Potential Costs Involved With/Without a Valid Warranty

If your rifle is covered by a valid warranty, it will be replaced at no cost to you. However, if your warranty has expired or is otherwise invalid, there may be costs associated with replacing it. These costs can vary depending on the specific situation, so its best to contact Remington directly for more information if this applies to you.

Warranty Coverage Costs

If your rifle is covered by a valid warranty, any costs associated with replacing it will be covered by that warranty. This includes shipping costs for returning the defective rifle as well as any parts or labor needed for the replacement process.

Non-Warranty Coverage Costs

If your rifle is not covered by a valid warranty, there may still be some costs associated with replacing it. These costs can include shipping fees for returning the defective rifle as well as any parts or labor needed for the replacement process that are not already covered under any warranties that may be in effect at the time of replacement. Additionally, there may also be additional fees that are imposed by Remington in order to cover administrative costs related to processing and replacing non-warranty firearms. Again, its best to contact Remington directly if this applies to you so that you can get an accurate estimate of what these costs might be before proceeding with any repairs or replacements.

Suggested Options for Ownership Protection and Liability Avoidance

In order to protect yourself from potential liability issues related to owning firearms, there are some steps you can take before and after purchasing them from retailers like Remington. One such measure is creating lock-up schemes for unused inventory and stock that can help prevent unauthorized access from occurring in your home or business establishment while still allowing authorized personnel access when needed. Additionally, there are also outlined liability reduction structures available through legal entities such as gun trusts which can help protect owners from potential liabilities in certain situations where ownership could potentially become an issue down the line (e.g., death). Its always advisable that gun owners seek out legal advice prior to engaging in any activities involving firearms ownership in order to ensure they understand all relevant laws and regulations pertaining thereto as well as their own specific rights and privileges under said laws/regulations prior to taking any further action related thereto

FAQ & Answers

Q: What is the Remington 710 Recall?
A: The Remington 710 recall was issued by the U.S. Consumer Product Safety Commission (CPSC) due to a defect in certain firearm models. The recall impacts specific serial number models of the Remington 710 rifle, which was manufactured between May 1, 2006 and April 9, 2014. The product defect involves a faulty firing pin safety mechanism that may fail to prevent the unintentional discharge of ammunition if the firearm is dropped or impacted forcefully in certain circumstances.

Q: Who is responsible for recalling the Remington 710?
A: The U.S. Consumer Product Safety Commission (CPSC) is responsible for issuing and overseeing the recall of all affected firearms models manufactured between May 1, 2006 and April 9, 2014 with noted serial numbers.

Q: How can I check if my Remington 710 is affected by the recall?
A: To check if your firearm is affected by this recall, you can either contact Remington Arms Company directly or input your serial number into their online search tool on their website to see if your model is included in this recall.

Q: What should I do if my Remington 710 model is included in the recall?
A: If your model of firearm is included in this recall, you should immediately stop using it and contact Remington Arms Company for further instructions on how to return it for a free replacement or refund. You can also find further instructions on how to return your recalled product on their website or contact them directly via phone or email for more information about this process.

Q: Are there any costs associated with replacing my recalled Remington 710?
A: If you have a valid warranty, then there will be no cost associated with returning and replacing your firearm through this recall process. However, if you do not have a valid warranty then there may be some associated costs depending on when you purchased or acquired your product and what type of coverage you have available through any other applicable policies or programs offered by Remington Arms Company at that time.

The Remington 710 was recalled in 2006 due to a manufacturing defect that could cause the rifle to fire without the trigger being pulled. The recall impacted rifles with serial numbers between R5130 and R6820. All owners of these rifles should contact Remington for information on how to return their rifle for a free repair or replacement.