How to Fix the Whirlpool Washer Error Code LOC – A Step-by-Step Guide

The Whirlpool Washer Loc Error Code indicates a problem with the machine’s primary control.

Whirlpool Washer Loc Error Code

Whirlpool washer loc error code is an error that occurs when the washers Cycle Control cannot detect the lid. It is usually caused by a faulty lid switch, which needs to be replaced in order to fix the problem. The LOC indicates that the washer recognizes that the lid is open, and has locked itself. This is a safety measure to ensure no potential harm can be caused by water escaping during drying and spinning cycles. When this error occurs, it will stop any further progress on the cycle and continuing to do so may cause damage to the appliance. The best solution is to unplug it and contact a Whirlpool service technician as soon as possible.

What is a Whirlpool Washer Loc Error Code?

A Whirlpool Washer Loc Error Code is a common malfunction that indicates a problem within the washer’s control panel. The code appears when the machine’s internal components are not communicating correctly, causing the washer to display a Loc error and refuse to start. This issue can occur due to a variety of reasons and can often be resolved with simple troubleshooting steps.

What Causes It?

The primary cause of the Whirlpool Washer Loc Error Code is an issue with the main control board or user interface components and connectors. The main control board is responsible for controlling all of the functions of the washer, while the user interface components allow users to select settings, adjust temperatures, and start cycles. If any of these components are damaged or malfunctioning, it can cause errors in communication between them and result in an error code.

How To Troubleshoot It?

The first step to troubleshooting this problem is to check the voltage supply source for the washer. If the power supply is functioning properly, then it may be necessary to reseat any connectors that are attached to the main control board or user interface components, as well as check all wiring harnesses for any loose connections or damages.

Common Solutions

If these troubleshooting steps do not resolve the issue, then it may be necessary to replace either the main control board or user interface components. Replacing either part requires some technical experience and should only be attempted by someone who understands how electrical systems work. Additionally, some common solutions include testing each component individually using a multimeter device and consulting service manuals or other troubleshooting procedures in order to diagnose any potential issues in greater detail.

Parts That Cause A Whirlpool Washer Loc Error Code

The most common parts that cause this error code are both found within the control panel of your washer: The main control board and user interface components/connectors. The main control board controls all functions within your washer such as cycle selection, temperature settings, etc., while user interface components allow you to interact with it by selecting settings and starting cycles. If either part malfunctions or becomes damaged due to wear and tear over time it can create issues in communication between them which will ultimately result in an error code being displayed on your washers screen.

How To Diagnose A Whirlpool Washer Loc Error Code Problem?

In order to properly diagnose a Whirlpool Washer Loc Error Code problem it is important to understand how each component works together. One way this can be done is through multimeter testing which allows you to measure voltage levels within each part in order to determine if they are functioning properly or not. Additionally, reviewing service manuals and other troubleshooting procedures can help you identify any potential issues more accurately so that they can be fixed more quickly and efficiently.

Steps To Fix A Whirlpool Washer Loc Error Code Problem

Once you have determined what part(s) need replacing or fixing in order to resolve your error code problem there are several steps you need take in order fix it:

Step One: Check The Voltage Supply Source Begin by checking whether there is power coming from your wall outlet into your washing machines power cord as well as ensuring that none of its internal circuits have been tripped due to an overload issue before attempting any other steps towards resolving your issue;

Step Two: Reseat The Connectors And Check The Wiring Harness After confirming that there is power coming into your machine you will now need inspect all connectors (such as those connecting your main control board/user interface) for any signs of damage or loose connections, as well as inspect all wiring harnesses for signs of fraying/rupture which could prevent proper communication between each component;

Step Three: Replace Any Damaged Parts If after inspecting everything no signs of damage are found then proceed by replacing any parts (mainly either a new main control board/user interface) which have been deemed faulty from testing with a multimeter device;

Step Four: Test Everything Again Finally once every step has been completed test everything again with a multimeter device one final time just make sure everything worked correctly before reassembling everything back together again;

Tools and Parts Needed To Repair a Whirlpool Washer Loc Error Code Problem

When it comes to repairing a Whirlpool washer that has experienced a LOC error code, there are certain tools and parts that must be available. The first of these is a multimeter, which is used for measuring voltage and resistance values. Additionally, spare parts may be needed for replacement purposes, depending on the issue at hand. Having the right tools and parts on hand will help make the repair process much smoother.

Tips to Avoid Getting A Whirlpool Washer Loc Error Code Again in Future

In order to prevent future occurrences of the Whirlpool washer LOC error code, it is important to take certain precautions. Firstly, all instructions should be followed carefully when connecting or replacing any parts of the washer. Additionally, it is wise to check on the integrity of any circuits regularly in order to ensure that they are working correctly. If any damaged components are spotted, they should be replaced as soon as possible in order to avoid potential issues. By taking these steps beforehand, you can avoid having to deal with this error code again in the future.

FAQ & Answers

Q: What is a Whirlpool Washer Loc Error Code?
A: A Whirlpool Washer Loc Error Code is an indication of a problem with the main control board or the user interface components. It typically occurs when the main control board is not communicating properly with the user interface components.

Q: What Causes a Whirlpool Washer Loc Error Code?
A: The Whirlpool Washer Loc Error Code is typically caused by a faulty main control board or user interface components. It could also be caused by damaged wiring, connectors, or other components.

Q: How to Troubleshoot a Whirlpool Washer Loc Error Code?
A: To troubleshoot a Whirlpool Washer Loc Error Code, you should first check the voltage supply source and then reseat the connectors and check the wiring harness. If these steps do not resolve the issue, then you may need to replace the main control board or test the user interface components.

Q: What Parts are Needed to Repair a Whirlpool Washer Loc Error Code Problem?
A: To repair a Whirlpool Washer Loc Error Code problem, you will need a multimeter for measuring voltage and resistance values, as well as spare parts for replacement purposes if needed.

Q: What Tips Can Help Avoid Getting A Whirlpool Washer Loc Error Code Again in Future?
A: In order to avoid getting a Whirlpool Washer Loc Error Code again in future, it is important to follow all instructions carefully while connecting/replacing parts, check on circuit integrity regularly, and replace any damaged components in a timely manner.

The Whirlpool Washer Loc Error Code is an indication that the washer is locked. It can occur when the control panel has been locked, when the lid is open, when a keypad button has been pressed for too long, or if the washer has experienced a power surge. In most cases, this code can be resolved by pressing the Pause/Cancel button on the control panel or unplugging and plugging back in the washer. If these steps do not resolve the issue, then it may be necessary to contact a certified appliance technician to further diagnose and repair the problem.